China factory High Flexibility T Series Spiral Bevel Gear Steering Gear Box for Changing Needs components of gearbox

Product Description

 

Product Features Description
Product Models T2, T4, T6, T7, T8, T10, T12, T16, T20, T25, Z2, Z4, Z6, Z7, Z8, Z10, Z12, Z16, Z20, Z25, JRTM2, JRTM4, JRTM6, JRTM7, JRTM8, JRTM10, JRTM12, JRTM16, JRTM20, JRTM25
Maintenance Clean internally and replace lubricant after initial use of 2 weeks or 100-200 hours. For long-term use, replace lubricant every half to 1 year or every 1000-2000 hours
Lubricant China Petroleum’s all-effect gear oil of 90-120 degrees. Under low speed and light load conditions, it is recommended to use all-effect gear oil of 90 degrees. Under heavy load and high temperature conditions, it is recommended to use all-effect gear oil of 120 degrees
Product Description The T series spiral bevel gear steering gearbox is widely used in food, pharmaceutical, chemical, steel, metallurgy, textile, plastic, paper and other machinery equipment, assembly lines and other industries
Technical Features The gearbox has a high rigidity FC-25 cast iron casing. The gears are made of high-quality high-purity alloy steel 20CrMnTi carburized and quenched, and ground. The shaft is tempered alloy steel with high load-bearing capacity. It is equipped with a heavy load-bearing tapered roller bearing. The oil seal has a double lip seal, which has dustproof and oil leakage prevention capabilities
Performance Features The T series spiral bevel gear steering gearbox is standardized and has many varieties. The speed ratio is all actual transmission ratios, with an average efficiency of 98%. It can run CHINAMFG and reverse, with smooth low-speed or high-speed transmission, low noise, small vibration, and large bearing force
Technical Parameters Speed ratio range: 1/1, 1.5/1, 2/1, 2.5/1, 3/1, 4/1, 5/1. Torque range: 11.2 – 5713 Nm. Power range: 0.014 – 335 kW

·Product Models: T2, T4, T6, T7, T8, T10, T12, T16, T20, T25, Z2, Z4, Z6, Z7, Z8, Z10, Z12, Z16, Z20, Z25, JRTM2, JRTM4, JRTM6, JRTM7, JRTM8, JRTM10, JRTM12, JRTM16, JRTM20, JRTM25.

·Maintenance: The gearbox should be cleaned internally and the lubricant should be replaced after the initial use of 2 weeks or 100-200 hours. For long-term use, the lubricant should be replaced every half to 1 year or every 1000-2000 hours.

·Lubricant: The product uses China Petroleum’s all-effect gear oil of 90-120 degrees. Under low speed and light load conditions, it is recommended to use all-effect gear oil of 90 degrees. Under heavy load and high temperature conditions, it is recommended to use all-effect gear oil of 120 degrees.

·Product Description: The T series spiral bevel gear steering gearbox is widely used in food, pharmaceutical, chemical, steel, metallurgy, textile, plastic, paper and other machinery equipment, assembly lines and other industries.

·Technical Features: The gearbox has a high rigidity FC-25 cast iron casing. The gears are made of high-quality high-purity alloy steel 20CrMnTi carburized and quenched, and ground. The shaft is tempered alloy steel with high load-bearing capacity. It is equipped with a heavy load-bearing tapered roller bearing. The oil seal has a double lip seal, which has dustproof and oil leakage prevention capabilities.

·Performance Features: The T series spiral bevel gear steering gearbox is standardized and has many varieties. The speed ratio is all actual transmission ratios, with an average efficiency of 98%. It can run CHINAMFG and reverse, with smooth low-speed or high-speed transmission, low noise, small vibration, and large bearing force.
RFQ

Q:What information should I tell you to confirm speed reducer?

A: Model/Size, Transmission Ratio, Shaft directions & Order quantity.

 

Q:What if I don’t know which gear reducer I need?

A:Don’t worry, Send as much information as you can, our team will help you find the right 1 you are looking for.

 

Q:What should I provide if I want to order NON-STANDERD speed reducers?

A: Drafts, Dimensions, Pictures and samples if possible.

 

Q:What is the MOQ?

A: It is OK for 1 or small pieces trial order for quality testing.

 

Q:How long should I wait for the feedback after I send the inquiry?

A: Within 6 hours

 

Q:What is the payment term?

A:You can pay via T/T(30% in advance+70% before delivery), L/C ,West Union etc
 

Application: Motor, Electric Cars, Motorcycle, Machinery, Marine, Toy, Agricultural Machinery, Car
Function: Distribution Power, Clutch, Change Drive Torque, Change Drive Direction, Speed Changing, Speed Reduction, Speed Increase
Layout: Coaxial
Hardness: Hardened Tooth Surface
Installation: Horizontal Type
Step: Three-Step
Samples:
US$ 100/Piece
1 Piece(Min.Order)

|
Request Sample

mover gearbox

Adjusting Tension on a Mower Gearbox Belt

Proper tension adjustment of the gearbox belt in your mower is crucial for optimal performance and belt longevity. Follow these steps to adjust the tension:

  1. Preparation: Turn off the mower’s engine and disconnect the spark plug wire to ensure safety.
  2. Locate the Adjustment Mechanism: Identify the tension adjustment mechanism on the mower. This could be a tensioning bolt, an adjustable bracket, or another mechanism depending on the mower model.
  3. Loosen Bolts: If your mower has tensioning bolts, slightly loosen the mounting bolts securing the gearbox in place. This allows the gearbox to move and adjust tension.
  4. Adjust Tension: Use the tension adjustment mechanism to increase or decrease the tension on the belt. Refer to your mower’s manual for recommended tension specifications.
  5. Check Tension: After adjusting, check the tension by pressing down on the belt at a midpoint between the pulleys. The belt should give a little, but not excessively. Also, check for proper alignment of the pulleys.
  6. Tighten Bolts: Once the tension is set correctly, tighten the mounting bolts of the gearbox to secure it in place.
  7. Test Operation: Reconnect the spark plug wire and start the mower to observe the belt’s operation. Listen for any unusual noises and monitor the belt for proper engagement with the pulleys.

Regularly checking and adjusting the tension of the gearbox belt ensures efficient power transmission and prevents premature wear. If you’re unsure about the proper tension adjustment, consult your mower’s manual or seek assistance from a professional.

mover gearbox

Lifespan of a Typical Mower Gearbox

The lifespan of a mower gearbox can vary depending on several factors, including the quality of the gearbox, maintenance practices, usage frequency, and operating conditions. On average, a well-maintained and high-quality mower gearbox can last between 5 to 10 years or even more.

Regular maintenance, such as checking and maintaining the oil level, cleaning and lubricating components, and addressing any issues promptly, can significantly extend the lifespan of a mower gearbox. Quality components, proper usage, and adherence to manufacturer guidelines also play a crucial role in determining how long a mower gearbox will last.

If you start noticing signs of wear, performance issues, or unusual noises from the gearbox, it’s important to address them promptly to prevent further damage and potentially extend the gearbox’s lifespan.

mover gearbox

Function of a Mower Gearbox

A mower gearbox operates through a series of gears and components that work together to transmit power and convert the rotational motion of the engine into the cutting action of the blades. Here’s how a typical mower gearbox works:

  1. Power Input: The mower gearbox receives power from the mower’s engine via a drive shaft.
  2. Gear Reduction: The gearbox contains a set of gears that are arranged in specific ratios to achieve the required torque and speed conversion. The input gear, connected to the drive shaft, meshes with one or more intermediate gears.
  3. Torque Conversion: As the input gear turns, it drives the intermediate gears. The gear arrangement within the gearbox results in a reduction of speed and an increase in torque. This is essential for providing the cutting blades with the necessary force to cut through vegetation.
  4. Blade Connection: The output shaft of the gearbox is connected to the cutting blades. As the gearbox output shaft rotates, it transfers the torque to the blades, causing them to spin.
  5. Blade Rotation: The rotational motion of the blades is what enables them to cut through grass and other vegetation. The increased torque generated by the gearbox allows the blades to effectively perform cutting or mulching actions.

Modern mower gearboxes are designed for efficiency, durability, and precision. They are often equipped with ball bearings, seals, and lubrication to minimize friction and ensure smooth operation. Some mower gearboxes also include additional features such as adjustable cutting heights, blade synchronization, and directional control to enhance the versatility of the mower.

China factory High Flexibility T Series Spiral Bevel Gear Steering Gear Box for Changing Needs   components of gearbox	China factory High Flexibility T Series Spiral Bevel Gear Steering Gear Box for Changing Needs   components of gearbox
editor by CX 2023-10-07