Gearbox for Rapeseed/Canola Harvester

Bearing kits (input & output), seal kits (all positions), matched gear pairs, shaft assemblies, overhaul kits, hardware packs. All ship within 24-48 hours.

How: Refer to your canola harvester manufacturer’s manual for the recommended header drive operating speed

Why it matters: Together with PTO speed, this defines the exact gear ratio your gearbox needs

How: Estimate your annual operating hours for the canola harvester to determine appropriate service life rating

Why it matters: Pengoperasian dengan jam kerja tinggi memerlukan spesifikasi bantalan dan roda gigi premium untuk biaya per jam terendah.

How: Record the brand, model number, and any part numbers from the nameplate of the gearbox being replaced

Why it matters: Speeds up the matching process and ensures dimensional compatibility with your canola harvesting equipment

How: Calculate the peak torque your rapeseed harvesting application generates — including shock loads from obstacles or material variations

Why it matters: Kotak roda gigi harus mampu menangani torsi puncak tanpa mengaktifkan perlindungan beban berlebih selama pengoperasian normal.

How: Match the gearbox HP rating to your tractor’s PTO horsepower output and the canola harvester’s demand

Why it matters: Kapasitas yang terlalu rendah menyebabkan panas berlebih dan kerusakan dini; kapasitas yang terlalu tinggi menambah biaya dan bobot yang tidak perlu.

How: Identify the coupling type on your canola harvester — keyed, splined, flanged, or hollow bore

Why it matters: Mismatched outputs require costly adapter couplings and introduce potential failure points

How: Assess exposure to dust, moisture, chemicals, and temperature extremes in your typical rapeseed harvesting conditions

Why it matters: Menentukan tingkat penyegelan yang sesuai, lapisan permukaan, dan spesifikasi material wadah.

Attach the gearbox output shaft to the canola harvester’s header drive drive coupling. For keyed connections, align the keyway and slide the coupling on, then secure with the retaining bolt and torque to specification. For splined outputs, apply anti-seize to the splines and verify full engagement before locking.

After the first 10 hours of field operation, re-torque all mounting bolts to specification. Check the oil level and top up if necessary. Inspect all seals for any signs of weeping. Verify the driveline guard is properly reinstalled. Record the installation date and hour-meter reading for future maintenance scheduling.

Align the PTO driveline with the gearbox input shaft and slide the yoke onto the splines until the locking mechanism engages. Verify the spline count matches (6-spline for 540 RPM, 21-spline for 1000 RPM). Check that driveline operating angles do not exceed 15° — excessive angles cause premature U-joint failure and vibration.

Clean the mounting flange on the canola harvester frame with a wire brush and solvent, removing all old sealant, rust, and debris. Inspect the mounting surface for cracks, stripped threads, or warping. Chase any damaged bolt threads with a tap. Apply a thin film of anti-seize compound to the mounting face if specified.

Locate the drain plug on the existing gearbox and position a catch container underneath. Remove the drain plug and allow all oil to drain completely — inspect the oil for metal particles or discolouration that may indicate internal wear. Record the old gearbox model number, mounting bolt size, and shaft dimensions for reference.

Remove the fill plug and slowly add the recommended gear oil until it reaches the level indicator. Use the lubricant grade specified in the gearbox documentation (typically SAE 80W-90 GL-5 or equivalent). Replace the fill plug and hand-tighten, then snug with a wrench. Verify the breather cap is clean and unobstructed.

Park the tractor on firm, level ground. Engage the parking brake and place wheel chocks. Turn off the engine and remove the key. Disconnect the PTO shaft from the canola harvester. Allow all components to cool completely before touching. Wear appropriate PPE including gloves and safety glasses.

Carefully lift the new Rapeseed/Canola Harvester gearbox into position on the mounting flange, aligning all bolt holes. Insert mounting bolts hand-tight first, confirming proper alignment. Once all bolts are started, torque them in a star (cross) pattern to the value specified in the installation manual. Verify the gearbox sits flush against the frame with no gaps.

Probable Cause: Stripped gear teeth or broken gear

Recommended Action: Check the overload protection device first — this is the most likely cause if the gearbox was recently subjected to a sudden overload. Replace the shear bolt or reset the slip clutch per the manual. If overload protection is intact, the gearbox has internal damage and requires professional service.

Probable Cause: Operating beyond rated horsepower or duty cycle

Recommended Action: Check oil level and grade against the specification. Clean all debris from the housing exterior — especially the cooling fins. If the canola harvester is being operated at or above the gearbox’s rated power, reduce forward speed or PTO load. Consider upgrading to synthetic gear oil for improved thermal performance.

Probable Cause: Loose internal components or retaining hardware

Recommended Action: A clunking sound specifically on PTO engagement (but not during operation) usually indicates driveline lash — check driveline telescoping tube for wear. If the clunk occurs during operation, it may indicate excessive gear backlash from internal wear. Have the gearbox inspected if the sound is progressive.

Probable Cause: Rust or debris on the input shaft splines

Recommended Action: Clean the input shaft splines with a wire brush and apply a light coat of anti-seize. Slowly rotate the PTO shaft while pushing to align the splines. If the splines will not engage, verify the spline count matches your PTO standard — 6-spline for 540 RPM, 21-spline for 1000 RPM.

Probable Cause: Insufficient lubricant or incorrect oil grade

Recommended Action: Drain and inspect oil for metal particles. Refill with correct grade. If noise persists after oil change, bearing or gear inspection is required. Contact support for rebuild guidance.

Every gearbox ships with: installation manual with torque specifications, lubrication and maintenance schedule, parts diagram with individual part numbers, warranty registration card, and a quality inspection certificate with the unit’s serial number and test results.

If you provide your equipment details before ordering and we confirm compatibility, fitment is guaranteed. In the rare event of a compatibility issue, we offer a no-questions-asked exchange or refund on unused gearboxes within 30 days of delivery. Our goal is to match you with the correct gearbox on the first order.

We offer tiered pricing starting from single-unit purchases, with meaningful discounts beginning at 5+ units. Dealer and OEM pricing structures are available for agricultural equipment retailers and canola harvester manufacturers. Contact our sales team for a formal quotation tailored to your volume requirements.

Setiap kotak roda gigi dikuras oli pengirimannya, dibungkus dengan film VCI (Vapor Corrosion Inhibitor), dan dikemas dalam kotak kayu lapis kokoh yang sesuai untuk pengiriman internasional. Kemasan ini melindungi dari kelembapan, benturan, dan korosi selama transit — bahkan untuk pengiriman ke properti terpencil di Australia melalui angkutan darat.

Garansi komprehensif 24 bulan kami mencakup semua cacat material dan pengerjaan, termasuk bantalan, roda gigi, segel, dan rumah. Garansi ini berlaku sejak tanggal pembelian dan didukung oleh sistem manajemen mutu bersertifikasi ISO kami. Program garansi diperpanjang tersedia untuk pesanan dalam jumlah besar dan pesanan armada.

We maintain compatibility databases covering canola harvester models from the past 25+ years. Most older models can be directly fitted with our current gearbox range. For discontinued or rare models, send us the mounting dimensions and shaft specifications, and we will confirm fitment or design a custom adapter.

Absolutely. We manufacture gearboxes with keyed, splined, flanged, hex, and hollow-bore output shaft configurations. If your canola harvester requires a non-standard output size, spline count, or connection type, our engineering team will design and machine it to your exact specifications at no additional lead time for common modifications.

Yes — every purchase includes access to our engineering support team for installation guidance, troubleshooting, maintenance advice, and parts ordering. Support is available via phone, email, and our online contact form. There is no charge for technical support during or after the warranty period.

We accept bank transfer, credit card, and purchase orders from established accounts. For large orders, we offer 30-day payment terms subject to credit approval. Orders can be placed through our website, by email, or by phone. Pro-forma invoices are available for pre-payment arrangements.

Ya — kami mengirimkan ke setiap kode pos di Australia, termasuk daerah terpencil dan regional. Kami menggunakan perusahaan pengiriman barang pertanian berpengalaman yang memahami urgensi kebutuhan peralatan musiman. Pengiriman ekspres tersedia untuk situasi kerusakan darurat, dan kami menyimpan stok untuk pengiriman segera model-model populer.