EP-MDH-40 Disc Mower Hub Gearbox

EP-MDH-40 Disc Mower Hub Gearbox

The EP-MDH-40 is a dedicated disc mower hub gearbox rated at 40 HP with a precision-machined flange mount. Hay producers and silage contractors depend on its balanced hub design and sealed lubrication system to deliver uniform disc speed across the entire cutter bar width during high-speed mowing.

SKU: cdda68b4b254 Kategori: Tag: , , , ,

Keterangan


EP-MDH-40 Disc Mower Hub Gearbox β€” Precision Power Transmission for Modern Mowing

Itu EP-MDH-40 represents the latest in gearbox pertanian engineering. With 40 HP capacity, N/A (Hub Drive) ratio configuration, and 15 Kg (approx.) optimized construction, it delivers the power density and reliability today’s farming operations require.

EP-MDH-40 Disc Mower Hub Gearbox

📈 EP-MDH-40 Technical Specifications

Parameter Spesifikasi
Nomor Model EP-MDH-40
Jenis Gearbox Disc Mower Hub Gearbox
Rasio Gigi N/A (Hub Drive)
Konfigurasi Gigi N/A
Modul Gigi N/A
Daya Terukur 40 HP
Kecepatan Masukan 540 rpm
Poros Masukan/Keluaran Flange mount hub
Berat Bersih 15 Kg (approx.)
Bahan Roda Gigi Baja Paduan 20CrMnTi, Dikarburisasi & Dikeraskan HRC 58-62
Bahan Perumahan Aluminum Alloy / Cast Iron
Perlindungan Segel Segel Oli Multi-Bibir NBR/FKM, Peringkat IP65+
Pelumasan Oli roda gigi SAE 80W-90 atau 85W-140 EP
Perawatan Permukaan Primer E-Coat + Lapisan Serbuk Poliester, Warna Merah

⭐ Fitur Utama & Keunggulan Teknik

⚙

Bolt-On Precision Flange Mount

Machined flange with dowel pin locations for accurate, repeatable tiller frame alignment, eliminating vibration-inducing misalignment during extended tillage runs.

⚗

Gear-Ground Tooth Flanks, Ra 0.5 ΞΌm

Post-heat-treatment gear grinding achieves consistent surface finish and AGMA Class 9 geometry, reducing running-in wear and extending time to first service.

🔒

Hardened Dowel-Pin Alignment

Two precision ground dowel pins locate the housing halves within 0.02 mm, guaranteeing gear centre distance accuracy and eliminating assembly-induced backlash.

⚡

Zinc Flake Anti-Corrosion Fasteners

All external bolts finished with zinc-flake coating (Delta-Protekt) rated for 720 hours of salt spray, preventing seized fasteners during later disassembly.

🔄

Interference-Fit Bearing Installation

All bearings installed with controlled interference fit using induction heating, preventing the spinning-in-bore failures common in slip-fit assemblies.

🔨

Hardened Shift Fork Mechanism

For multi-ratio models: induction-hardened shift fork and detent system provides positive gear engagement with tactile confirmation, preventing half-engagement damage.

Mower gearbox in agricultural use

πŸ”§ Kompatibilitas dan Referensi Silang Peralatan

🔄 Cross-Reference Compatibility for EP-MDH-40

The EP-MDH-40 is engineered as a direct replacement or upgrade for gearboxes fitted to equipment from leading manufacturers including:

Iseki • YTO • Massey Ferguson • Deutz-Fahr • Woods • Krone • McConnel • Fendt

Penafian: Nama merek di atas hanya dirujuk untuk identifikasi kompatibilitas. Ever-power Australia Mower Gearbox Co.,Ltd. tidak berafiliasi dengan, didukung oleh, atau diotorisasi oleh produsen mana pun yang tercantum. Semua merek dagang milik pemiliknya masing-masing.

πŸ“š Panduan Pemilihan Transmisi

Selecting a gearbox that matches your exact requirements avoids premature wear and costly downtime. Consider these points for the EP-MDH-40:

📌 Weight and Mounting Considerations
At 15 Kg (approx.), the EP-MDH-40 is designed for disc mower cutter bars. Confirm your implement frame and three-point hitch can support this weight plus the weight of the blade assembly. Mounting bolt pattern and orientation should match your existing layout.
πŸ“Œ Menyesuaikan Rasio Gigi dengan Kecepatan Ujung Pisau
For the EP-MDH-40 with ratio(s) N/A (Hub Drive), calculate your required blade tip speed: typically 4,500-5,500 m/min for standard rotary cutters, 3,000-4,000 m/min for heavy brush cutting, and 5,500-6,500 m/min for fine finish mowing. Output RPM = PTO RPM Γ· ratio. Multiply by blade diameter to get tip speed.
πŸ“Œ Penentuan Ukuran Daya yang Sesuai dengan Daya PTO Traktor
The EP-MDH-40 is rated at 40 HP. Always select a gearbox rated at or above your tractor’s maximum PTO horsepower. For shock-load applications (mulching, brush clearing), add a 25-30% safety margin: a 60 HP tractor should use a 75+ HP rated gearbox.
πŸ“Œ Pilihan PTO 540 RPM vs 1000 RPM
The EP-MDH-40 operates at 540 rpm. Most rotary mowers use 540 RPM PTO. The 1000 RPM standard is for larger implements on high-HP tractors. Never connect a 540 RPM gearbox to a 1000 RPM PTO β€” the doubled speed will destroy bearings and gears within minutes.
πŸ“Œ Casing Besi Cor vs Casing Aluminium
The EP-MDH-40 uses a aluminium alloy or cast iron housing. Cast iron excels in vibration damping, impact resistance, and heat dissipation β€” ideal for rough, rocky mowing conditions. Aluminium is lighter and more corrosion-resistant, better suited to wet environments and weight-sensitive implements.

🌾 Skenario Aplikasi Umum

🌾 Conservation tillage and minimum-disturbance cultivation

🚘 Railway corridor vegetation control programs

🌱 Estate, golf course, and sportsfield maintenance

⛰ Flail mulching of pruning residue in fruit plantations

🌳 Orchard and vineyard floor maintenance between rows

Ever-power Australia Mower Gearbox Co.,Ltd. manufacturing facility

πŸ›  Panduan Instalasi & Pengaturan

  1. For units weighing over 25 kg, use a chain hoist, engine crane, or two-person lift to position the gearbox. Never attempt to lift heavy gearboxes solo.
  2. Fill the gearbox with the recommended gear oil (SAE 80W-90 or 85W-140 EP) to the level indicated on the sight glass or dipstick. Do not overfill.
  3. Before operating at full load, run through a graduated break-in sequence: 30 minutes at half-throttle, then 30 minutes at three-quarter throttle, before engaging full PTO speed.
  4. Inspect the implement mounting pad for flatness using a straightedge. Any warping exceeding 0.5 mm should be corrected before the new gearbox is installed.
  5. Use Nord-Lock washers or thread-locking compound on all mounting bolts to prevent vibration-induced loosening during operation.
  6. Run the gearbox at no load for 5-10 minutes, then shut down and re-check oil level β€” new seals and bearings often absorb a small amount of initial oil.
  7. Bersihkan permukaan tempat pemasangan alat secara menyeluruh, hilangkan semua karat, sisa material paking lama, serpihan cat, dan kotoran yang dapat menghalangi kontak yang rapat dengan flensa gearbox.

❓ Pertanyaan yang Sering Diajukan

❓ What shipping methods are available?

Sea freight (20-35 days), air freight (5-10 days), and express courier (3-5 days) worldwide. Sea freight is most economical for bulk orders. All shipments include protective packaging, documentation, and full tracking.

❓ Can this unit directly replace my OEM gearbox?

Yes. Our mounting patterns, shaft diameters, and spline profiles match industry-standard OEM dimensions. We supply detailed technical drawings for cross-referencing. If your existing unit differs slightly, our engineering team can advise on adapters.

❓ What happens if I accidentally run it dry?

Stop the PTO immediately. Even a few minutes without oil causes severe gear scoring and bearing damage, typically requiring a full internal rebuild. Always verify oil level before engaging the PTO.

❓ How should I store the gearbox off-season?

Run briefly to warm the oil, then top up to the full mark. Apply grease to exposed shaft surfaces and seal any open ports. Store in a dry, covered area. Before next season, verify oil level and rotate input by hand to check free movement.

❓ Can I replace just the gear set?

Yes. Replacement gear sets are available for all models and are cost-effective when the housing, bearings, and shafts remain in good condition. We recommend replacing bearings and seals simultaneously for best results.

⭐ Ulasan Pelanggan & Laporan Lapangan

★★★★★

πŸ“ Queensland, Australia

Third year of heavy use on our orchard floor management. Still going strong with just regular oil changes. The best aftermarket gearbox I have found.

★★★★★

📍 Kent, England

Good gearbox with a solid, hefty feel. Delivery to England was fast. Only needed a small spacer washer to fit our older mower model.

★★★★★

📍 SΓ£o Paulo, Brazil

Handles our Mediterranean conditions well β€” wet winters and dry summers. This gearbox just keeps working without fuss.

★★★★☆

📍 SkΓ₯ne, Sweden

Bought for heavy vineyard maintenance work. Dust, heat, debris β€” it handles everything. The seals are particularly impressive in dirty conditions.

★★★★☆

📍 Alentejo, Portugal

Solid replacement unit. Took minimal effort to install. Once running, it is smooth and efficient. Good value for money.

Rentang gearbox pertanian

⚖ EP-MDH-40 vs. Low-Cost Alternatives

Fitur EP-MDH-40 (Ever-power) Alternatif Generik / Murah
Housing Machining ✔ 5-Axis CNC, IT6 Bore Tolerance ✘ 3-Axis CNC or Manual, IT9 Bore Tolerance
Spare Parts Availability ✔ Full Inventory, Ships Within 24 Hours ✘ Limited Stock, 4-8 Week Back-Order
Lead Time ✔ 3-5 Days Standard, 4-6 Weeks Custom ✘ 8-12 Weeks, No Expedite Option
Gear Accuracy ✔ AGMA Class 8-10, CNC Ground Post Heat-Treatment ✘ AGMA Class 5-6, Hobbed Only, No Grinding
Kapasitas Minyak ✔ Generous Sump for Extended Cooling, Sight Glass ✘ Minimal Oil Volume, No Level Indicator
Drain Plug ✔ Magnetic Plug Captures Wear Particles ✘ Standard Plug, No Particle Capture
Traceability ✔ Laser-Etched Serial, Full Material Records ✘ No Serial Number, No Traceability

🔄 Related Products & Accessories

🏆 Certifications & Quality Standards

The EP-MDH-40 is produced in our ISO 9001:2015 certified facility with full material traceability from steel mill to finished product. We perform incoming material inspection (spectrometry and hardness), in-process dimensional verification at every machining stage, and final assembly testing that includes noise, vibration, and oil-leak checks. Certificates of conformance are available on request.

🏭 Why Choose Ever-power Australia Mower Gearbox Co.,Ltd.?

Choosing Ever-power Australia Mower Gearbox Co.,Ltd. means partnering with a manufacturer that understands agricultural machinery from the ground up. Our R&D team develops 12 new gearbox models each year, collaborating directly with implement OEMs in Australia, Germany, the United States, Brazil, and beyond. Whether you need a standard catalog gearbox shipped next week or a fully custom design with unique ratios and mounting interfaces, we deliver β€” on specification, on budget, and on time.

PTO drive shaft

📞 Get Your EP-MDH-40 Quote Today

Upgrade from unreliable aftermarket gearboxes to the proven EP-MDH-40. Our team is ready to provide datasheets, cross-reference guides, and a no-obligation quotation within 24 hours.

Request a QuoteBrowse All Products

Produk Terkait