Skrzynia biegów do kombajnu do pomidorów

Professional-Grade Tomato Harvester Gearbox — Trusted by Farmers Across Australia

Productive tomato harvesting starts with dependable power transmission. The Tomato Harvester gearbox we manufacture is a precision instrument — not a commodity part. In a tomato harvester, the gearbox drives the cutting bar, shaker bed, and electronic sorting conveyor. The gear reduction must deliver gentle yet effective shaking action to separate fruit from vines without bruising, making gear precision particularly important in this application.

From the hardened gear teeth to the heavy-duty shaft seals, every element is selected and assembled to deliver thousands of hours of trouble-free service. Australian farmers operating in dust, heat, mud, and moisture rely on this gearbox to perform consistently throughout the most demanding seasons.

🛠 Tomato Harvester Gearbox Specifications at a Glance

Kluczowe dane dotyczące naszej wydajności agricultural gearbox for tomato harvesterPotrzebujesz innych specyfikacji? Produkujemy dokładnie według Twoich wymagań.

Skontaktuj się z nami zespół inżynierski for a detailed specification sheet tailored to your tomato harvester model and tomato harvesting conditions.

🏆 Performance Advantages — Why Our Tomato Harvester Gearbox Leads the Field

Not all tomato harvester gearboxes are equal. Here is an objective comparison showing why our Tomato Harvester gearbox delivers substantially better value:

Quality Metric	Economy-Class Unit	Our Professional Tomato Harvester Gearbox
System uszczelniający	Single-lip NBR rubber seal, no dust excluder	Cassette-type metal-cased seal with integrated dirt rejection lip
Specyfikacja łożyska	Budget ball bearings, C3 clearance, unknown origin	Premium tapered roller bearings, precision pre-loaded, 10,000-hr L10 life
Wydajność operacyjna	88-92% — noticeable temperature rise during operation	96-98.5% — validated across full load range, not just peak efficiency point
Części zapasowe	Części różnią się w zależności od partii	Full inventory, ships 24-48 hours
Surface Protection	Bare casting with thin oil film	Hot-dip galvanized option for extreme environments
Projektowanie mieszkań	Welded steel fabrication, dimensional inconsistency	Precision die-cast housing, vacuum-impregnated to eliminate micro-porosity

The numbers speak clearly: superior materials, tighter tolerances, and longer service life add up to a gearbox that costs less per operating hour than any alternative on the market. Get in touch to discuss your requirements.

⚙ Tomato Harvester Gearbox — Complete Power Transmission Analysis

Zrozumienie wewnętrznych mechanizmów Twojego tomato harvester gearbox pozwala zoptymalizować wydajność i wykryć wczesne oznaki zużycia.

Etap 1: Odbiór mocy WOM

The gearbox input shaft connects to your tractor’s PTO via a splined coupling (6-spline at 540 RPM or 21-spline at 1000 RPM). Precision needle roller bearings absorb the combined radial and thrust loads generated during tomato harvesting. On this tomato harvesting machine, the PTO driveline feeds energy into the gearbox at the tomato harvester’s primary drive point.

Etap 2: Redukcja przełożeń i konwersja momentu obrotowego

Inside the housing, precisely meshed helical gears convert PTO high-speed input into modified speed and amplified torque for the shaker/conveyor drive. In a tomato harvester, the gearbox drives the cutting bar, shaker bed, and electronic sorting conveyor. The gear reduction must deliver gentle yet effective shaking action to separate fruit from vines without bruising, making gear precision particularly important in this application. Gear tooth profiles are case-hardened to HRC 58-62 and precision-ground, achieving 96-98% mechanical efficiency.

Stage 3: Output to the Shaker/Conveyor Drive

Power exits through the output shaft connecting to the tomato harvester’s shaker/conveyor drive. The output configuration (keyed, splined, flanged, or hollow bore) matches the implement’s drive requirements. Smooth power flow to the shaker/conveyor drive is maintained regardless of load fluctuations during tomato harvesting.

Etap 4: Smarowanie i kontrola termiczna

The nodular iron housing acts as a heat sink with cooling fins for convective cooling. Internal splash lubrication with SAE 80W-140 multi-grade ensures all surfaces maintain a protective oil film. Double-Lip Oil Seals at each shaft opening block contaminants while retaining lubricant.

✅ Verified Replacements for Major Tomato Harvester Brands

Odniesienia do marek służą wyłącznie ułatwieniu klientom identyfikacji kompatybilnych skrzyń biegów. Wszystkie znaki towarowe należą do ich odpowiednich właścicieli.

Our Tomato Harvester agricultural gearbox is a verified drop-in replacement for these brands and models:

• Fendt: G8.2, Mk-I, H-745 — ✅ dimensionally verified
• CLAAS: G4.5, Series 638, Mk-IV — ✅ dimensionally verified
• Geringhoff: Model 4967, E-832, 467S — ✅ dimensionally verified
• Claas: J-351, Model 1914, Type 52C — ✅ dimensionally verified
• Kverneland: Series 109, H-200, 250X — ✅ dimensionally verified

Long-Term Parts Guarantee

We guarantee parts availability for every Tomato Harvester gearbox we sell. Bearing kits, seal packs, gear sets, shafts — all stocked and ready for express dispatch. Fleet customers receive dedicated parts support and volume pricing.

🎯 Tomato Harvester Gearbox Sizing Guide — Get the Right Fit First Time

Getting the right gearbox for your tomato harvesting machine requires confirming these seven parameters before you order. Our engineering team can help you through each step if needed.

1. Power Requirement
Match the gearbox HP rating to your tractor’s PTO horsepower output and the tomato harvester’s demand.
Ważne: Niedoszacowanie parametrów prowadzi do przegrzania i przedwczesnej awarii, natomiast przeszacowanie parametrów powoduje niepotrzebne koszty i wagę.

2. Existing Gearbox Identification
Record the brand, model number, and any part numbers from the nameplate of the gearbox being replaced.
Importance: Speeds up the matching process and ensures dimensional compatibility with your tomato harvesting machine.

3. Working Hours per Season
Estimate your annual operating hours for the tomato harvester to determine appropriate service life rating.
Znaczenie: Praca o dużej liczbie godzin uzasadnia stosowanie łożysk i przekładni o wyższej jakości, co pozwala na osiągnięcie najniższych kosztów na godzinę.

4. Torque Demand
Calculate the peak torque your tomato harvesting application generates — including shock loads from obstacles or material variations.
Importance: The gearbox must handle peak torque without activating overload protection during normal operation.

5. Mounting Bolt Pattern
Measure the bolt hole positions, centre distances, and overall envelope on your tomato harvester’s gearbox mounting flange.
Znaczenie: Zapewnia bezpośredni montaż za pomocą śrub, bez konieczności stosowania żadnych dodatkowych elementów lub płyt adapterowych.

6. Prędkość WOM ciągnika
Sprawdź specyfikację WOM swojego ciągnika — standardowo wynosi 540 obr./min lub 1000 obr./min.
Znaczenie: Określa rozmiar wielowypustu wału wejściowego i punkt wyjścia do obliczenia przełożenia.

7. Kierunek obrotu
Determine whether the shaker/conveyor drive on your tomato harvester requires clockwise or counter-clockwise output when viewed from the drive end.
Ważne: Nieprawidłowy kierunek obrotów może uszkodzić narzędzie lub uniemożliwić wykonanie jakiejkolwiek pracy.

💡 Wskazówka: Wskazówka dotycząca zamawiania: w przypadku wymiany istniejącej skrzyni biegów, należy zmierzyć co najmniej średnice wału wejściowego/wyjściowego oraz rozstaw śrub montażowych. Dzięki tym trzem wymiarom nasz zespół może dobrać odpowiednią jednostkę z naszego katalogu lub zaprojektować rozwiązanie niestandardowe.

🔧 Technician’s Installation Manual — Tomato Harvester Gearbox

Follow these instructions for a successful installation of your new Tomato Harvester gearbox. Correct installation is critical for achieving maximum service life and warranty coverage.

Step 1: Safety Preparation

Park the tractor on firm, level ground. Engage the parking brake and place wheel chocks. Turn off the engine and remove the key. Disconnect the PTO shaft from the tomato harvester. Allow all components to cool completely before touching. Wear appropriate PPE including gloves and safety glasses.

Step 2: Drain & Document Old Gearbox

Locate the drain plug on the existing gearbox and position a catch container underneath. Remove the drain plug and allow all oil to drain completely — inspect the oil for metal particles or discolouration that may indicate internal wear. Record the old gearbox model number, mounting bolt size, and shaft dimensions for reference.

Step 3: Remove Old Gearbox

Disconnect the PTO driveline from the gearbox input shaft. Support the gearbox weight with a floor jack or overhead hoist (typical weight: 15-70 kg depending on model). Remove all mounting bolts in a criss-cross pattern to relieve clamping stress evenly. Carefully lower the old gearbox and set it aside.

Step 4: Position & Secure New Gearbox

Carefully lift the new Tomato Harvester gearbox into position on the mounting flange, aligning all bolt holes. Insert mounting bolts hand-tight first, confirming proper alignment. Once all bolts are started, torque them in a star (cross) pattern to the value specified in the installation manual. Verify the gearbox sits flush against the frame with no gaps.

Step 5: Post-Installation Checks (10-Hour Service)

After the first 10 hours of field operation, re-torque all mounting bolts to specification. Check the oil level and top up if necessary. Inspect all seals for any signs of weeping. Verify the driveline guard is properly reinstalled. Record the installation date and hour-meter reading for future maintenance scheduling.

Step 6: Connect Output to shaker/conveyor drive

Attach the gearbox output shaft to the tomato harvester’s shaker/conveyor drive drive coupling. For keyed connections, align the keyway and slide the coupling on, then secure with the retaining bolt and torque to specification. For splined outputs, apply anti-seize to the splines and verify full engagement before locking.

Step 7: Connect PTO Driveline

Align the PTO driveline with the gearbox input shaft and slide the yoke onto the splines until the locking mechanism engages. Verify the spline count matches (6-spline for 540 RPM, 21-spline for 1000 RPM). Check that driveline operating angles do not exceed 15° — excessive angles cause premature U-joint failure and vibration.

Step 8: Test Run & Break-In

Start the tractor and engage the PTO at low RPM (approximately 300 RPM). Listen carefully for any grinding, whining, knocking, or clicking sounds. Run at low speed for 15-20 minutes, monitoring the gearbox housing temperature by hand (carefully). Check for oil leaks at all seals and the mounting interface. Gradually increase to full operating speed.

⚠ Ważne: Always consult the specific installation manual shipped with your Tomato Harvester gearbox for model-specific torque values and procedures.

🔧 Problem-Solving: Tomato Harvester Gearbox Field Issues

Use this diagnostic reference to identify and resolve common Tomato Harvester gearbox issues in the field. Most problems can be diagnosed and addressed without removing the gearbox from the tomato harvester.

⚠ Skrzynia biegów pracuje nadmiernie

Probable Cause: Niewłaściwy gatunek oleju (zbyt gęsty lub zbyt rzadki do danych warunków)

Recommended Action: Check oil level and grade against the specification. Clean all debris from the housing exterior — especially the cooling fins. If the tomato harvester is being operated at or above the gearbox’s rated power, reduce forward speed or PTO load. Consider upgrading to synthetic gear oil for improved thermal performance.

⚠ Skrzynia biegów wydaje metaliczny dźwięk stukania podczas włączania WOM

Probable Cause: Luźny mechanizm zabezpieczający przed przeciążeniem

Recommended Action: A clunking sound specifically on PTO engagement (but not during operation) usually indicates driveline lash — check driveline telescoping tube for wear. If the clunk occurs during operation, it may indicate excessive gear backlash from internal wear. Have the gearbox inspected if the sound is progressive.

⚠ Trudności z połączeniem układu napędowego WOM ze skrzynią biegów

Probable Cause: Nieprawidłowa liczba linii krzywych (niezgodność 540 i 1000 obr./min)

Recommended Action: Clean the input shaft splines with a wire brush and apply a light coat of anti-seize. Slowly rotate the PTO shaft while pushing to align the splines. If the splines will not engage, verify the spline count matches your PTO standard — 6-spline for 540 RPM, 21-spline for 1000 RPM.

⚠ Wał wyjściowy przestaje się obracać, podczas gdy wał wejściowy się obraca

Probable Cause: Wewnętrzne złamanie trzonu

Recommended Action: Check the overload protection device first — this is the most likely cause if the gearbox was recently subjected to a sudden overload. Replace the shear bolt or reset the slip clutch per the manual. If overload protection is intact, the gearbox has internal damage and requires professional service.

⚠ Abnormal Grinding or Whining Noise

Probable Cause: Foreign object trapped in gear mesh

Recommended Action: Drain and inspect oil for metal particles. Refill with correct grade. If noise persists after oil change, bearing or gear inspection is required. Contact support for rebuild guidance.

If any issue cannot be resolved with the actions above, contact our technical support team for expert diagnosis. We can arrange remote troubleshooting or dispatch a replacement unit for critical breakdown situations.

📈 Engineer’s Field Notes — Tomato Harvester Gearbox Installations

Our agricultural gearboxes are field-proven across every Australian state and territory. Below are documented case studies from recent Tomato Harvester gearbox installations.

📚 Tomato Harvester Gearbox — Your Questions Answered

🔹 What minimum order is needed for volume pricing?

We offer tiered pricing starting from single-unit purchases, with meaningful discounts beginning at 5+ units. Dealer and OEM pricing structures are available for agricultural equipment retailers and tomato harvester manufacturers. Contact our sales team for a formal quotation tailored to your volume requirements.

🔹 Will this gearbox fit older-model tomato harvester equipment?

We maintain compatibility databases covering tomato harvester models from the past 25+ years. Most older models can be directly fitted with our current gearbox range. For discontinued or rare models, send us the mounting dimensions and shaft specifications, and we will confirm fitment or design a custom adapter.

🔹 Which gear oil do you recommend for Australian conditions?

For most Australian climates, SAE 80W-90 EP gear oil meeting GL-5 specification is ideal. In tropical regions with sustained high temperatures, we recommend 85W-140. For southern regions experiencing cold winters, synthetic 75W-90 provides better cold-start protection. Check the oil specification card shipped with your gearbox for the definitive recommendation.

🔹 What gear ratios are available for the tomato harvester gearbox?

We offer a comprehensive range of ratios from 1:1 through 1:6 to match virtually any tomato harvester configuration. Standard catalogue ratios ship within days; custom ratios can be manufactured within 2-3 weeks. Our engineers will recommend the optimal ratio based on your tractor PTO speed and tomato harvesting requirements.

🔹 Can I return a gearbox if it does not fit my tomato harvester?

If you provide your equipment details before ordering and we confirm compatibility, fitment is guaranteed. In the rare event of a compatibility issue, we offer a no-questions-asked exchange or refund on unused gearboxes within 30 days of delivery. Our goal is to match you with the correct gearbox on the first order.

🔹 Do you provide technical support after purchase?

Tak — każdy zakup obejmuje dostęp do naszego zespołu wsparcia technicznego, który udziela wskazówek dotyczących instalacji, rozwiązywania problemów, udziela porad dotyczących konserwacji i zamawiania części. Wsparcie jest dostępne telefonicznie, mailowo i za pośrednictwem naszego formularza kontaktowego online. Wsparcie techniczne jest bezpłatne w okresie gwarancyjnym i po jego zakończeniu.

🔹 What does the warranty cover and for how long?

Our 24-month comprehensive warranty covers all defects in materials and workmanship, including bearings, gears, seals, and housing. It applies from the date of purchase and is backed by our ISO-certified quality management system. Extended warranty programs are available for bulk and fleet orders.

🔹 How do I determine the correct gearbox model for my equipment?

Provide us with your tractor brand/model and PTO speed, the tomato harvester manufacturer and model, and the old gearbox part number if available. Alternatively, measure the input/output shaft dimensions and mounting bolt pattern. Our selection engineers will identify the correct match, typically within 24 hours.

🔹 Can this gearbox withstand the shock loads generated during tomato harvesting?

The gearbox is specifically designed for the dynamic and impact loading characteristic of tomato harvesting applications. Case-hardened alloy steel gears absorb repetitive shocks, while the optional overload protection (shear bolt or slip clutch) safeguards against catastrophic overload events. The bearing selection and housing rigidity are both matched to tomato harvester load profiles.

🔹 What is the expected lifespan under continuous tomato harvesting operation?

Our Tomato Harvester gearbox is rated for 3,000 to 5,000+ operating hours with proper maintenance. Many customers in intensive Australian operations report achieving 5,000+ hours before requiring any internal service. Key factors affecting lifespan include oil change frequency, operating load, and environmental conditions.

⚙ Build a Reliable Tomato Harvesting Powertrain

Maximize your tomato harvesting equipment reliability with these complementary products designed to work with our Tomato Harvester gearbox.

Komponenty układu napędowego WOM Constant-velocity PTO shafts for high-angle tomato harvesting installations. Overload protection included. Matching splines for direct connection to our gearbox range. Odkryj wały odbioru mocy →

Kolekcja skrzyń biegów rolniczych Our agricultural gearbox collection covers every major implement category. Each unit is precision-manufactured and backed by our 24-month warranty. Zobacz wszystkie skrzynie biegów →

⚖ Safety Standards for Tomato Harvester Equipment in Australia

Operating tomato harvester equipment in Australia requires compliance with federal and state workplace health and safety legislation. Key requirements for Tomato Harvester gearbox installations include:

Standards Compliance

Standard	Relevance
Safe Work Australia PTO Safety Guidelines	All PTO-driven tomato harvester equipment must incorporate compliant shaft guarding. Guard-compatible drivelines available.
AS/NZS 3788 — Pressure Equipment	Obudowy przekładni bezpiecznie utrzymują wewnętrzne ciśnienia robocze zgodnie z obowiązującymi normami.

State-Level WHS Requirements

• ACT — Rozporządzenie w sprawie bezpieczeństwa i higieny pracy z 2011 r.: mirrors national standards for agricultural machinery including tomato harvester equipment.
• Terytorium Północne — Przepisy WHS (jednolite ustawodawstwo krajowe) z 2011 r.: applies federal standards to tomato harvesting operations territory-wide.
• Tasmania — Przepisy WHS 2012: mandates operator training for all PTO-driven tomato harvester equipment.

Australia-Wide Tomato Harvester Gearbox Distribution

Dostarczamy Tomato Harvester agricultural gearboxes to every state and territory in Australia. Our logistics network covers major farming regions including the Atherton Tablelands, the Burdekin, and Mackay-Whitsunday, the Wheatbelt, the Ord River district, and the Great Southern, and the Darling Downs, the Lockyer Valley, and the Burnett region. Whether you operate in a metropolitan fringe area or a remote pastoral station, we ship directly to your property with full tracking and delivery confirmation.

🎯 Your Tomato Harvester Gearbox Journey Starts Here

Poza standardem — witamy w niestandardowych rozwiązaniach

Standard specifications don’t always fit. Our engineering team designs and manufactures custom gearboxes to your drawings, samples, or specifications. From modified OEM replacements to completely new designs for specialised tomato harvester equipment — we handle it all.

Twój zaufany partner w zakresie rozwiązań dla skrzyń biegów w maszynach rolniczych — standardowych i niestandardowych — w Australii i na całym świecie.