Gearbox for Corn Harvester

Disconnect the PTO driveline from the gearbox input shaft. Support the gearbox weight with a floor jack or overhead hoist (typical weight: 15-70 kg depending on model). Remove all mounting bolts in a criss-cross pattern to relieve clamping stress evenly. Carefully lower the old gearbox and set it aside.

Start the tractor and engage the PTO at low RPM (approximately 300 RPM). Listen carefully for any grinding, whining, knocking, or clicking sounds. Run at low speed for 15-20 minutes, monitoring the gearbox housing temperature by hand (carefully). Check for oil leaks at all seals and the mounting interface. Gradually increase to full operating speed.

Park the tractor on firm, level ground. Engage the parking brake and place wheel chocks. Turn off the engine and remove the key. Disconnect the PTO shaft from the corn harvester. Allow all components to cool completely before touching. Wear appropriate PPE including gloves and safety glasses.

Clean the mounting flange on the corn harvester frame with a wire brush and solvent, removing all old sealant, rust, and debris. Inspect the mounting surface for cracks, stripped threads, or warping. Chase any damaged bolt threads with a tap. Apply a thin film of anti-seize compound to the mounting face if specified.

Locate the drain plug on the existing gearbox and position a catch container underneath. Remove the drain plug and allow all oil to drain completely — inspect the oil for metal particles or discolouration that may indicate internal wear. Record the old gearbox model number, mounting bolt size, and shaft dimensions for reference.

Carefully lift the new Corn Harvester gearbox into position on the mounting flange, aligning all bolt holes. Insert mounting bolts hand-tight first, confirming proper alignment. Once all bolts are started, torque them in a star (cross) pattern to the value specified in the installation manual. Verify the gearbox sits flush against the frame with no gaps.

Align the PTO driveline with the gearbox input shaft and slide the yoke onto the splines until the locking mechanism engages. Verify the spline count matches (6-spline for 540 RPM, 21-spline for 1000 RPM). Check that driveline operating angles do not exceed 15° — excessive angles cause premature U-joint failure and vibration.

After the first 10 hours of field operation, re-torque all mounting bolts to specification. Check the oil level and top up if necessary. Inspect all seals for any signs of weeping. Verify the driveline guard is properly reinstalled. Record the installation date and hour-meter reading for future maintenance scheduling.

Probable Cause: Failed key or spline on output shaft

Recommended Action: Check the overload protection device first — this is the most likely cause if the gearbox was recently subjected to a sudden overload. Replace the shear bolt or reset the slip clutch per the manual. If overload protection is intact, the gearbox has internal damage and requires professional service.

Probable Cause: Bearing wear or race damage

Recommended Action: Drain and inspect oil for metal particles. Refill with correct grade. If noise persists after oil change, bearing or gear inspection is required. Contact support for rebuild guidance.

Probable Cause: Blocked breather vent preventing pressure relief

Recommended Action: First, check and correct the oil level — overfilling is a surprisingly common cause of seal leaks. Clean or replace the breather cap. If oil level is correct and breather is clear, the seal has worn and should be replaced using our seal kit.

Probable Cause: PTO driveline too long, causing impact on engagement

Recommended Action: A clunking sound specifically on PTO engagement (but not during operation) usually indicates driveline lash — check driveline telescoping tube for wear. If the clunk occurs during operation, it may indicate excessive gear backlash from internal wear. Have the gearbox inspected if the sound is progressive.

Probable Cause: Debris-clogged cooling fins reducing heat dissipation

Recommended Action: Check oil level and grade against the specification. Clean all debris from the housing exterior — especially the cooling fins. If the corn harvester is being operated at or above the gearbox’s rated power, reduce forward speed or PTO load. Consider upgrading to synthetic gear oil for improved thermal performance.

Each gearbox is drained of shipping oil, wrapped in VCI (Vapor Corrosion Inhibitor) film, and crated in a sturdy plywood box rated for international freight. This packaging protects against moisture, impact, and corrosion during transit — even for shipments to remote Australian properties via road freight.

We offer a comprehensive range of ratios from 1:1 through 1:6 to match virtually any corn harvester configuration. Standard catalogue ratios ship within days; custom ratios can be manufactured within 2-3 weeks. Our engineers will recommend the optimal ratio based on your tractor PTO speed and corn harvesting requirements.

We accept bank transfer, credit card, and purchase orders from established accounts. For large orders, we offer 30-day payment terms subject to credit approval. Orders can be placed through our website, by email, or by phone. Pro-forma invoices are available for pre-payment arrangements.

För de flesta australiska klimat är SAE 80W-90 EP-växellådsolja som uppfyller GL-5-specifikationen idealisk. I tropiska områden med ihållande höga temperaturer rekommenderar vi 85W-140. För södra regioner som upplever kalla vintrar ger syntetisk 75W-90 bättre kallstartskydd. Kontrollera oljespecifikationskortet som medföljer din växellåda för den definitiva rekommendationen.

Våra växellådor är mekaniska komponenter och innehåller inga ämnen som skulle kunna påverka ekologisk certifiering. Valet av smörjmedel bör dock övervägas – vi kan rekommendera livsmedelsgodkända och biologiskt nedbrytbara växellådsoljor som är kompatibla med ekologiska jordbruksstandarder i Australien och internationellt.

Om du anger dina utrustningsuppgifter innan du beställer och vi bekräftar kompatibilitet garanteras passformen. I de sällsynta fall av kompatibilitetsproblem erbjuder vi ett byte eller återbetalning utan frågor på oanvända växellådor inom 30 dagar efter leverans. Vårt mål är att matcha dig med rätt växellåda vid första beställningen.

Our Corn Harvester gearbox is rated for 3,000 to 5,000+ operating hours with proper maintenance. Many customers in intensive Australian operations report achieving 5,000+ hours before requiring any internal service. Key factors affecting lifespan include oil change frequency, operating load, and environmental conditions.

The gearbox is specifically designed for the dynamic and impact loading characteristic of corn harvesting applications. Case-hardened alloy steel gears absorb repetitive shocks, while the optional overload protection (shear bolt or slip clutch) safeguards against catastrophic overload events. The bearing selection and housing rigidity are both matched to corn harvester load profiles.

Absolutely. We manufacture gearboxes with keyed, splined, flanged, hex, and hollow-bore output shaft configurations. If your corn harvester requires a non-standard output size, spline count, or connection type, our engineering team will design and machine it to your exact specifications at no additional lead time for common modifications.

Vår 24-månaders omfattande garanti täcker alla defekter i material och utförande, inklusive lager, kugghjul, tätningar och hus. Den gäller från inköpsdatum och backas upp av vårt ISO-certifierade kvalitetsledningssystem. Utökade garantiprogram är tillgängliga för bulk- och flottordrar.