Gearbox for Fertilizer Spreader

Advanced Fertilizer Spreader Gearbox — Optimal Torque Delivery for Fertilizer Distribution

The agricultural gearbox is the mechanical heart of every fertilizer spreader. Ours is purpose-built for fertilizer distribution — converting PTO energy into dependable, high-torque output that keeps your spreading implement working at peak capacity. Located beneath the hopper, the fertilizer spreader gearbox powers one or two spinning discs that fling granular fertilizer outward. The gear ratio determines disc speed and therefore spread width, while the robust construction withstands the corrosive nature of chemical fertilizers.

Manufactured from premium alloy steels with precision CNC machining, this Fertilizer Spreader gear drive delivers measurably superior efficiency compared to generic replacements. Every unit ships fully tested, lubricated, and ready for immediate installation on your equipment.

Fertilizer Spreader Agricultural Gearbox

📈 Technical Specifications — Fertilizer Spreader Gearbox

Below are the standard specifications for our fertilizer spreader gearbox. All parameters can be customized to match your specific fertilizer distribution requirements.

Parameter	Standard Value	Custom Options
Empfohlenes Schmiermittel	SAE 80W-140 Mehrbereichsöl	Kompatibel mit synthetischen und Bioölen
Eingangswellenverzahnung	6-Zahn (1-3/8″) / 21-Zahn (1-3/4″)	20-Zahn-Ausführung, 8-Zahn-Ausführung auf Anfrage
Schmierverfahren	Splash/bath	Zwangsschmierung für hohe Belastungszyklen
Oberflächenbeschichtung	Hot-dip galvanized	RAL-Sonderfarben erhältlich
Ausgangsdrehzahlbereich	150 – 1370 RPM	Hängt vom gewählten Verhältnis ab
Wellendichtungstyp	Cassette Seal	Dreifachlippen- und Kassettenoptionen
Output Shaft Type	Keyed shaft	Custom output configurations
Noise at 1m Distance	≤ 68 dB(A)	Low-noise profiles optional
Zapfwellen-Eingangsdrehzahl	540 / 1000 U/min	Sparsame Zapfwelle (750 U/min) optional erhältlich
Designstandard	DIN 3990	Zertifizierung durch Dritte
Gegenreaktion	≤ 10 Bogenminuten	Option mit reduziertem Spiel
Abtriebswellendurchmesser	35 mm	Anpassung zur Implementierung der Kopplung
Ölkapazität	3.4 litres	Übergroßer Sumpf verfügbar
Centre Distance	160 mm	Per gear ratio
Oberflächenhärte der Zahnräder	HRC 57 – 65	Aufgekohlt + geschliffen
Gehäusematerial	High-Strength Steel Alloy	Material-Upgrades optional
Maximum Continuous Torque	80 – 1500 Nm	Peak torque: 150% of continuous
Bearing Design Life (L10)	5000 hours minimum	Extended-life configurations
Drehrichtung	Bidirektional	Reversible Modelle
Entlüftungsventil	Entlüfter aus Sinterbronze	Allwettertypen

Kontaktieren Sie uns Ingenieurteam for a detailed specification sheet tailored to your fertilizer spreader model and fertilizer distribution conditions.

💪 Quality Comparison — Fertilizer Spreader Gearbox

We believe in transparency. These are the specific, verifiable differences between our Fertilizer Spreader gear drive and low-cost alternatives:

Spezifikation	Low-Cost Alternative	Our Engineered Fertilizer Spreader Gearbox
Oberflächenschutz	No primer — surface rust within weeks	Hot-dip galvanized option for extreme environments
Garantie & Support	12-month warranty excludes seals and bearings	Volle 2-Jahres-Garantie + Techniker-Hotline + Installationsunterstützung
Lärm und Vibrationen	85+ dB(A) — requires hearing protection	Computeroptimiertes Kontaktmuster reduziert Vibrationen 60% im Vergleich zum Standard
Lagerspezifikation	Budget ball bearings, C3 clearance, unknown origin	Doppelreihige Kegelrollen, Option für dauergekapselte Schmierung
Ersatzteile	No individual parts — must buy complete gearbox	Full inventory, ships 24-48 hours
Gear Material & Treatment	Cast steel, surface-hardened only, shallow case	SAE 8620 alloy, gas-carburized + tempered, superfinished tooth flanks
Betriebseffizienz	85-90% — significant power loss as heat	96-98.5% — validated across full load range, not just peak efficiency point

Bottom Line: Budget fertilizer spreader gearboxes may save 30-40% upfront but cost 3-5x more through failures and lost productivity. Our Fertilizer Spreader gearbox is the professional’s choice.

Fertilizer Spreader application

⚙ How the Fertilizer Spreader Gearbox Works — Mechanical Principles

Here is how our Fertilizer Spreader gearbox converts PTO output into productive fertilizer distribution power:

▶ Power Input — PTO Connection

Your tractor’s PTO shaft engages with the gearbox through a hardened splined input shaft. The interface transmits torque while allowing minor angular misalignment. Inside, deep groove ball bearings support the input shaft and manage the combined loading of transmitted torque and driveline forces.

▶ Gear Reduction — Torque Conversion

Precision crown gears inside the gearbox reduce PTO speed while multiplying torque to match the spinner disc’s demands. Located beneath the hopper, the fertilizer spreader gearbox powers one or two spinning discs that fling granular fertilizer outward. The gear ratio determines disc speed and therefore spread width, while the robust construction withstands the corrosive nature of chemical fertilizers. The gears are manufactured from carburized alloy steel, ground to tight tolerances, and profiled for quiet, efficient power transfer.

▶ Power Output — Spinner Disc Drive

The gearbox output shaft connects directly to the fertilizer spreader’s spinner disc, delivering torque-multiplied power for productive fertilizer distribution. The output coupling is machined to precise tolerances for responsive, zero-backlash power delivery.

▶ Thermal & Environmental Management

The gearbox uses splash lubrication with SAE 85W-140 EP. Gears distribute oil across all contact surfaces. The grey cast iron housing incorporates cooling ribs that dissipate heat under sustained fertilizer distribution load. Double-Lip Oil Seals at every shaft exit prevent contamination ingress.

🔁 Direct Interchange — Fertilizer Spreader Gearbox Compatibility

Cross-reference data is provided as a customer service. All brand names and model numbers remain the intellectual property of their respective owners.

Click each manufacturer below to see verified compatible fertilizer spreader models:

Solis ✅

Compatible models: 922S, G1.0, J-728. Direct bolt-on replacement — no modifications required.

Geringhoff ✅

Compatible models: Model 6043, G6.7, Mk-V. Direct bolt-on replacement — no modifications required.

Branson ✅

Compatible models: Type 42J, Mk-IV, Series 152. Direct bolt-on replacement — no modifications required.

Deutz-Fahr ✅

Compatible models: 292S, Mk-II, Type 98C. Direct bolt-on replacement — no modifications required.

Mahindra ✅

Compatible models: Series 958, Mk-III, C-600. Direct bolt-on replacement — no modifications required.

Parts & Service Support

Bearing rebuild kits with spacers and shims
Seal & gasket replacement kits
Matched gear pairs — pinion and wheel
Input and output shaft assemblies

📚 Quick Selection Guide — Choosing the Right Fertilizer Spreader Gearbox

Selecting the correct gearbox for your fertilizer spreader is essential for achieving optimal fertilizer distribution performance. Follow this checklist:

Step	What to Confirm	How to Determine	Why It Matters
1	Mounting Bolt Pattern	Measure the bolt hole positions, centre distances, and overall envelope on your fertilizer spreader’s gearbox mounting flange	Gewährleistet die direkte Verschraubung ohne jegliche Anpassungen oder Adapterplatten
2	Working Hours per Season	Estimate your annual operating hours for the fertilizer spreader to determine appropriate service life rating	Bei hohem Betriebsstundenbedarf sind Premium-Lager- und Getriebespezifikationen erforderlich, um die niedrigsten Kosten pro Stunde zu erzielen.
3	Tractor PTO Speed	Prüfen Sie die Zapfwellenspezifikation Ihres Traktors – Standard sind 540 U/min oder 1000 U/min.	Bestimmt die Größe der Eingangswellenverzahnung und die Basis für die Übersetzungsberechnung
4	Operating Environment	Assess exposure to dust, moisture, chemicals, and temperature extremes in your typical fertilizer distribution conditions	Bestimmt die geeignete Dichtungsklasse, Oberflächenbeschichtung und Gehäusematerialspezifikation
5	Power Requirement	Match the gearbox HP rating to your tractor’s PTO horsepower output and the fertilizer spreader’s demand	Unterdimensionierung führt zu Überhitzung und vorzeitigem Ausfall; Überdimensionierung verursacht unnötige Kosten und Gewicht.
6	Drehrichtung	Determine whether the spinner disc on your fertilizer spreader requires clockwise or counter-clockwise output when viewed from the drive end	Incorrect rotation direction will damage the implement or produce no useful work
7	Torque Demand	Calculate the peak torque your fertilizer distribution application generates — including shock loads from obstacles or material variations	Das Getriebe muss im Normalbetrieb das maximale Drehmoment bewältigen können, ohne den Überlastschutz auszulösen.

💡 Profi-Tipp: If you are unsure about any parameter, photograph the existing gearbox nameplate and mounting area and send the images to our team via our contact page. We will identify the correct replacement within 24 hours.

Sammlung von Landwirtschaftsgetrieben

🔧 Step-by-Step Installation — Fertilizer Spreader Gearbox

Follow these instructions for a successful installation of your new Fertilizer Spreader gearbox. Correct installation is critical for achieving maximum service life and warranty coverage.

Step 1: Post-Installation Checks (10-Hour Service)

After the first 10 hours of field operation, re-torque all mounting bolts to specification. Check the oil level and top up if necessary. Inspect all seals for any signs of weeping. Verify the driveline guard is properly reinstalled. Record the installation date and hour-meter reading for future maintenance scheduling.

Step 2: Prepare the Mounting Surface

Clean the mounting flange on the fertilizer spreader frame with a wire brush and solvent, removing all old sealant, rust, and debris. Inspect the mounting surface for cracks, stripped threads, or warping. Chase any damaged bolt threads with a tap. Apply a thin film of anti-seize compound to the mounting face if specified.

Step 3: Connect PTO Driveline

Richten Sie die Nebenantriebswelle an der Getriebeeingangswelle aus und schieben Sie die Gabel auf die Verzahnung, bis der Verriegelungsmechanismus einrastet. Prüfen Sie, ob die Anzahl der Verzahnungen übereinstimmt (6 Verzahnungen für 540 U/min, 21 Verzahnungen für 1000 U/min). Achten Sie darauf, dass die Betriebswinkel der Antriebswelle 15° nicht überschreiten – zu große Winkel führen zu vorzeitigem Verschleiß der Kreuzgelenke und Vibrationen.

Step 4: Test Run & Break-In

Starten Sie den Traktor und schalten Sie die Zapfwelle bei niedriger Drehzahl (ca. 300 U/min) ein. Achten Sie genau auf mahlende, heulende, klopfende oder klickende Geräusche. Lassen Sie den Traktor 15–20 Minuten mit niedriger Drehzahl laufen und überwachen Sie dabei vorsichtig die Temperatur des Getriebegehäuses von Hand. Prüfen Sie alle Dichtungen und die Befestigungspunkte auf Öllecks. Erhöhen Sie die Drehzahl allmählich auf volle Betriebsdrehzahl.

Step 5: Connect Output to spinner disc

Attach the gearbox output shaft to the fertilizer spreader’s spinner disc drive coupling. For keyed connections, align the keyway and slide the coupling on, then secure with the retaining bolt and torque to specification. For splined outputs, apply anti-seize to the splines and verify full engagement before locking.

Step 6: Drain & Document Old Gearbox

Suchen Sie die Ablassschraube am vorhandenen Getriebe und stellen Sie einen Auffangbehälter darunter. Entfernen Sie die Ablassschraube und lassen Sie das gesamte Öl ablaufen. Prüfen Sie das Öl auf Metallpartikel oder Verfärbungen, die auf inneren Verschleiß hindeuten könnten. Notieren Sie sich die Modellnummer des alten Getriebes, die Größe der Befestigungsschrauben und die Wellenabmessungen.

Schritt 7: Sicherheitsvorbereitung

Park the tractor on firm, level ground. Engage the parking brake and place wheel chocks. Turn off the engine and remove the key. Disconnect the PTO shaft from the fertilizer spreader. Allow all components to cool completely before touching. Wear appropriate PPE including gloves and safety glasses.

Step 8: Fill With Lubricant

Entfernen Sie die Einfüllschraube und füllen Sie langsam das empfohlene Getriebeöl bis zur Markierung ein. Verwenden Sie die in der Getriebedokumentation angegebene Viskositätsklasse (üblicherweise SAE 80W-90 GL-5 oder gleichwertig). Setzen Sie die Einfüllschraube wieder ein und ziehen Sie sie handfest, anschließend mit einem Schraubenschlüssel fest. Stellen Sie sicher, dass die Entlüftungskappe sauber und frei ist.

⚠ Wichtig: Always consult the specific installation manual shipped with your Fertilizer Spreader gearbox for model-specific torque values and procedures.

🔧 Problem-Solving: Fertilizer Spreader Gearbox Field Issues

Use this diagnostic reference to identify and resolve common Fertilizer Spreader gearbox issues in the field. Most problems can be diagnosed and addressed without removing the gearbox from the fertilizer spreader.

⚠ Öl tritt an den Wellendichtungen aus

Probable Cause: Worn lip seals or damaged seal bore

Recommended Action: First, check and correct the oil level — overfilling is a surprisingly common cause of seal leaks. Clean or replace the breather cap. If oil level is correct and breather is clear, the seal has worn and should be replaced using our seal kit.

⚠ Output Shaft Stops Turning While Input Rotates

Probable Cause: Shear bolt or overload protection has activated

Recommended Action: Check the overload protection device first — this is the most likely cause if the gearbox was recently subjected to a sudden overload. Replace the shear bolt or reset the slip clutch per the manual. If overload protection is intact, the gearbox has internal damage and requires professional service.

⚠ Ungewöhnliche mahlende oder heulende Geräusche

Probable Cause: Worn or pitted gear tooth surfaces

Recommended Action: Drain and inspect oil for metal particles. Refill with correct grade. If noise persists after oil change, bearing or gear inspection is required. Contact support for rebuild guidance.

⚠ Schwierigkeiten beim Verbinden des Nebenabtriebsstrangs mit dem Getriebe

Probable Cause: Misaligned splines due to different PTO standard

Recommended Action: Clean the input shaft splines with a wire brush and apply a light coat of anti-seize. Slowly rotate the PTO shaft while pushing to align the splines. If the splines will not engage, verify the spline count matches your PTO standard — 6-spline for 540 RPM, 21-spline for 1000 RPM.

⚠ Getriebe läuft übermäßig heiß

Probable Cause: Insufficient oil volume or degraded lubricant

Recommended Action: Check oil level and grade against the specification. Clean all debris from the housing exterior — especially the cooling fins. If the fertilizer spreader is being operated at or above the gearbox’s rated power, reduce forward speed or PTO load. Consider upgrading to synthetic gear oil for improved thermal performance.

If any issue cannot be resolved with the actions above, contact our technical support team for expert diagnosis. We can arrange remote troubleshooting or dispatch a replacement unit for critical breakdown situations.

📈 Engineer’s Field Notes — Fertilizer Spreader Gearbox Installations

Our agricultural gearboxes are field-proven across every Australian state and territory. Below are documented case studies from recent Fertilizer Spreader gearbox installations.

📍 Case #1: Adelaide, SA

Kunde:	Mark Sullivan — broadacre cropping operation
Standort:	Adelaide, SA
Betriebsgröße:	1000 acres
Anwendung:	Fertilizer Spreader gearbox for fertilizer spreader — fertilizer distribution
Kaufgrund:	Replace failed OEM gearbox to restore fertilizer spreader for the upcoming season

“The technical support was exceptional. They asked detailed questions about our setup, recommended the correct model and ratio, and followed up after installation to confirm everything was operating correctly. That level of service is rare.”
— Mark Sullivan, Adelaide, SA

David Thompson — Renmark, SA

Betrieb: corporate farming entity | Größe: 3000 acres | Verwenden: Fertilizer Spreader gearbox for fertilizer distribution

Kaufgrund: Upgrade von einem günstigen Nachrüstgerät, das weniger als eine Saison hielt.

“Installed as a replacement for a gearbox that catastrophically failed mid-season. The MowerGearbox unit was delivered within 6 days and fitted perfectly. We finished the season without further issues. Very impressed.”

📍 Narrabri, NSW commercial fertilizer distribution contractor — 3000 acres

Kunde: Derek Whitfield | Anwendung: Fertilizer Spreader gearbox — fertilizer distribution

Zweck: Retrofit older model fertilizer spreader with improved gearbox for extended service life

“Fast delivery to a remote location was the initial reason I tried this supplier. The gearbox quality is what made me a repeat customer — we have now standardised on their products across our fleet of 7 fertilizer spreader machines.”

📍 Case #4: Katanning, WA

Kunde:	Fred Nolan — cooperative farming group
Standort:	Katanning, WA
Betriebsgröße:	4000 acres
Anwendung:	Fertilizer Spreader gearbox for fertilizer spreader — fertilizer distribution
Kaufgrund:	Fleet standardisation — transitioning all fertilizer spreader equipment to a single gearbox supplier

„Qualität vergleichbar mit europäischen Originalteilen zum halben Preis. Die Verarbeitung ist sauber, der Lack haltbar und die Zahnräder laufen spürbar geschmeidiger als das chinesische Gerät, das es ersetzt hat. Habe es bereits drei anderen Landwirten empfohlen.“
— Fred Nolan, Katanning, WA

Jack Thornton — Horsham, VIC

Betrieb: large-scale pastoral property | Größe: 1000 acres | Verwenden: Fertilizer Spreader gearbox for fertilizer distribution

Kaufgrund: Custom ratio requirement for a modified fertilizer spreader not served by standard catalogues

“The oil-tight sealing on this gearbox is remarkable. After 574 hours of operation in dusty paddocks, the oil comes out clean at service time. Previous gearboxes always had contaminated oil by the first oil change.”

📚 Fertilizer Spreader Gearbox — Your Questions Answered

🔹 What documentation ships with the gearbox?

Jedes Getriebe wird mit folgendem Lieferumfang geliefert: Montageanleitung mit Drehmomentangaben, Schmier- und Wartungsplan, Teilezeichnung mit Einzelteilenummern, Garantieschein und Qualitätsprüfzertifikat mit Seriennummer und Testergebnissen.

🔹 Which gear oil do you recommend for Australian conditions?

Für die meisten australischen Klimazonen ist SAE 80W-90 EP-Getriebeöl gemäß GL-5-Spezifikation ideal. In tropischen Regionen mit anhaltend hohen Temperaturen empfehlen wir 85W-140. Für südliche Regionen mit kalten Wintern bietet synthetisches 75W-90 einen besseren Kaltstartschutz. Die endgültige Empfehlung finden Sie auf dem mit Ihrem Getriebe gelieferten Öldatenblatt.

🔹 Can I return a gearbox if it does not fit my fertilizer spreader?

Wenn Sie uns vor der Bestellung Ihre Gerätedaten mitteilen und wir die Kompatibilität bestätigen, ist der Einbau garantiert. Sollte es ausnahmsweise zu Kompatibilitätsproblemen kommen, bieten wir Ihnen innerhalb von 30 Tagen nach Lieferung einen unkomplizierten Umtausch oder eine Rückerstattung für unbenutzte Getriebe an. Unser Ziel ist es, Ihnen bereits bei der ersten Bestellung das passende Getriebe zu liefern.

🔹 Can this gearbox withstand the shock loads generated during fertilizer distribution?

The gearbox is specifically designed for the dynamic and impact loading characteristic of fertilizer distribution applications. Case-hardened alloy steel gears absorb repetitive shocks, while the optional overload protection (shear bolt or slip clutch) safeguards against catastrophic overload events. The bearing selection and housing rigidity are both matched to fertilizer spreader load profiles.

🔹 What is the expected lifespan under continuous fertilizer distribution operation?

Our Fertilizer Spreader gearbox is rated for 3,000 to 5,000+ operating hours with proper maintenance. Many customers in intensive Australian operations report achieving 5,000+ hours before requiring any internal service. Key factors affecting lifespan include oil change frequency, operating load, and environmental conditions.

🔹 How do I determine the correct gearbox model for my equipment?

Provide us with your tractor brand/model and PTO speed, the fertilizer spreader manufacturer and model, and the old gearbox part number if available. Alternatively, measure the input/output shaft dimensions and mounting bolt pattern. Our selection engineers will identify the correct match, typically within 24 hours.

🔹 Do you deliver to remote farming areas in Australia?

Ja – wir liefern an jede Postleitzahl in Australien, auch in abgelegene und ländliche Gebiete. Wir arbeiten mit erfahrenen Speditionen für Agrartransporte zusammen, die den dringenden Bedarf an saisonalen Geräten kennen. Für Notfälle bieten wir Expressversand an und haben gängige Modelle auf Lager, um sie sofort versenden zu können.

🔹 What gear ratios are available for the fertilizer spreader gearbox?

We offer a comprehensive range of ratios from 1:1 through 1:6 to match virtually any fertilizer spreader configuration. Standard catalogue ratios ship within days; custom ratios can be manufactured within 2-3 weeks. Our engineers will recommend the optimal ratio based on your tractor PTO speed and fertilizer distribution requirements.

🔹 Can the output shaft be customized for my specific fertilizer spreader?

Absolutely. We manufacture gearboxes with keyed, splined, flanged, hex, and hollow-bore output shaft configurations. If your fertilizer spreader requires a non-standard output size, spline count, or connection type, our engineering team will design and machine it to your exact specifications at no additional lead time for common modifications.

🔹 Do you provide technical support after purchase?

Ja – jeder Kauf beinhaltet den Zugang zu unserem technischen Support-Team für Installationsanleitungen, Fehlerbehebung, Wartungshinweise und Ersatzteilbestellungen. Sie erreichen uns telefonisch, per E-Mail und über unser Online-Kontaktformular. Der technische Support ist während und nach der Garantiezeit kostenlos.

🔧 Essential Accessories for Fertilizer Spreader Applications

A complete power transmission system delivers better results than any single component. Consider these additions to your Fertilizer Spreader setup.

PTO Drive Shaft Assembly

Agricultural PTO shaft assemblies with shear-bolt or friction-clutch overload protection. Available in lengths from 600mm to 2500mm for any tractor-to-fertilizer spreader distance.

View PTO Shafts →

Full Gearbox Catalogue

Looking for gearboxes for other farm implements? Our product line spans tillage, harvesting, baling, spraying, and specialty applications.

Browse Gearboxes →

📜 Australian Compliance & Regulations — Fertilizer Spreader Gearboxes

Operating fertilizer spreader equipment in Australia requires compliance with federal and state workplace health and safety legislation. Key requirements for Fertilizer Spreader gearbox installations include:

Applicable Standards

Safe Work Australia PTO Safety Guidelines: All PTO-driven fertilizer spreader equipment must incorporate compliant shaft guarding. Guard-compatible drivelines available.
ISO 12100 — Safety of Machinery: Gearbox design follows the general principles of risk assessment and risk reduction for fertilizer distribution equipment.

State-Specific Requirements

New South Wales — Work Health and Safety Regulation 2017: requires documented maintenance records for all power-driven fertilizer spreader machinery.
Northern Territory — WHS (National Uniform Legislation) Regulations 2011: applies federal standards to fertilizer distribution operations territory-wide.
Victoria — OHS Regulations 2017: specifies risk assessment requirements for fertilizer distribution machinery operations.

Regional Coverage & Delivery Network

Wir liefern Fertilizer Spreader agricultural gearboxes to every state and territory in Australia. Our logistics network covers major farming regions including the Barossa Valley, the Riverland, and South East SA, the Darling Downs, the Lockyer Valley, and the Burnett region, and the Midlands and North West TAS. Whether you operate in a metropolitan fringe area or a remote pastoral station, we ship directly to your property with full tracking and delivery confirmation.

🚨 Upgrade Your Fertilizer Spreader — Talk to Our Engineers

Agricultural Gearbox Factory

Manufacturing Excellence — 15+ Experience

We are a professional manufacturer of agricultural gearboxes and PTO drive systems. Our facility features:

Complete vertical integration — from raw forgings to finished assemblies
Temperature-controlled assembly environment for consistent bearing pre-load
Dedicated R&D team for custom and prototype gearbox development
Full CAD/CAM design with FEA stress analysis
Automated heat treatment with atmosphere-controlled furnaces

Custom & Non-Standard Manufacturing

We specialise in non-standard, custom-designed gear drives built to your exact requirements. Whether you need a unique ratio, modified housing, non-standard shaft, or a bespoke gearbox for your fertilizer spreader, we deliver — from prototype to volume production.

Send us your drawings, samples, or specifications — and receive a quotation within 24 hours.

📧 Request a Quote

🏭 Learn About Our Company →

Ihr zuverlässiger Partner für Getriebelösungen in der Landwirtschaft – Standard- und Sonderanfertigungen – in ganz Australien und weltweit.