EP-01-707 Lawn Mower Gearbox

EP-01-707 Lawn Mower Gearbox

The EP-01-707 pairs a 1:1.44 ratio with module 6 gears and 1 3/4 Z20 spline input to deliver 60 HP reliably. Municipal councils and highway departments select this model for its balance of output speed, torque, and service weight — heavy enough for durability, light enough for standard three-point hitch mounting.

SKU: 42432a702cff Categoría: Etiquetas: , , , ,

Descripción


EP-01-707 — Professional-Grade Medium-Duty Rotary Cutter Gearbox for Agricultural Mowing

El EP-01-707 is a purpose-engineered lawn mower gearbox delivering reliable right-angle power transmission at 60 HP with 540 rpm PTO input. Its spiral bevel gears and sealed construction ensure consistent performance across thousands of operating hours in demanding field conditions.

EP-01-707 Medium-Duty Rotary Cutter Gearbox

📈 EP-01-707 Technical Specifications

Parámetro Especificación
Número de modelo EP-01-707
Tipo de caja de cambios Medium-Duty Rotary Cutter Gearbox
Relación(es) de transmisión 1:1.44
Configuración de los dientes 23/16
Módulo de engranajes 6
Potencia nominal 60 HP
Velocidad de entrada 540 rpm
Eje de entrada/salida 1 3/4 Z20 / Taper spline
Peso neto 37 Kg
Material de engranajes Acero aleado 20CrMnTi, carburizado y endurecido HRC 58-62
Material de vivienda Grey Cast Iron (HT200/HT250)
Protección de sellado Retenes de aceite multilabios NBR/FKM, con clasificación IP65+
Lubricación Aceite para engranajes SAE 80W-90 o 85W-140 EP
Tratamiento de superficies Imprimación electroforética + recubrimiento en polvo de poliéster, acabado rojo.

⭐ Características clave y ventajas de ingeniería

🔒

Pressurized Internal Oil Pump

Gear-driven micro-pump maintains positive lubrication pressure at all critical contacts, enabling safe operation on slopes exceeding 40° without oil starvation.

⚡

Lightweight AlSi7Mg T6 Housing

Aluminum-silicon alloy housing with T6 temper provides excellent thermal conductivity for cooler operation and natural corrosion resistance in wet haymaking environments.

🔄

Sealed-for-Life Bearing Pack

Bearings factory-packed with Mobil XHP 222 high-temp grease, delivering 1,500 hours of maintenance-free disc mower operation before re-greasing is needed.

🔨

Space-Optimized Thin-Wall Enclosure

Compact aluminum or thin-wall iron casing for applications where overall gearbox envelope and weight are hard-limited by implement frame constraints.

🌡

Multi-Position Bolt Pattern

Versatile mounting interface with tapped holes at 0°, 90°, and 180° orientations, fitting a wide range of implement frame geometries without adapter plates.

🛠

E-Coat + Powder Coat Finish

25 μm zinc-rich e-coat primer plus 80 μm polyester powder topcoat provides 1,000+ hours of ASTM B117 salt-spray corrosion resistance.

Caja de engranajes de segadora para uso agrícola

🔧 Compatibilidad de equipos y referencias cruzadas

🔄 Cross-Reference Compatibility for EP-01-707

The EP-01-707 is engineered as a direct replacement or upgrade for gearboxes fitted to equipment from leading manufacturers including:

Massey Ferguson • Deutz-Fahr • Woods • Krone • McConnel • Fendt • Iseki • YTO

Descargo de responsabilidad: Las marcas mencionadas anteriormente se utilizan únicamente para identificar la compatibilidad. Ever-power Australia Mower Gearbox Co., Ltd. no está afiliada, respaldada ni autorizada por ninguno de los fabricantes mencionados. Todas las marcas registradas pertenecen a sus respectivos propietarios.

📚 Guía de selección de cajas de cambios

Choosing the right mower gearbox is critical for implement performance and longevity. Use the following criteria when evaluating the EP-01-707:

📌 Adaptación de la relación de engranajes a la velocidad de la punta de la cuchilla
For the EP-01-707 with ratio(s) 1:1.44, calculate your required blade tip speed: typically 4,500-5,500 m/min for standard rotary cutters, 3,000-4,000 m/min for heavy brush cutting, and 5,500-6,500 m/min for fine finish mowing. Output RPM = PTO RPM ÷ ratio. Multiply by blade diameter to get tip speed.
📌 Dimensionamiento de la potencia nominal en relación a la potencia de la toma de fuerza del tractor (HP)
The EP-01-707 is rated at 60 HP. Always select a gearbox rated at or above your tractor’s maximum PTO horsepower. For shock-load applications (mulching, brush clearing), add a 25-30% safety margin: a 60 HP tractor should use a 75+ HP rated gearbox.
📌 Selección de toma de fuerza (PTO) de 540 RPM frente a 1000 RPM
The EP-01-707 operates at 540 rpm. Most rotary mowers use 540 RPM PTO. The 1000 RPM standard is for larger implements on high-HP tractors. Never connect a 540 RPM gearbox to a 1000 RPM PTO — the doubled speed will destroy bearings and gears within minutes.
📌 Cast Iron Housing vs Aluminium Housing
The EP-01-707 uses a grey cast iron housing. Cast iron excels in vibration damping, impact resistance, and heat dissipation — ideal for rough, rocky mowing conditions. Aluminium is lighter and more corrosion-resistant, better suited to wet environments and weight-sensitive implements.
📌 Standard Catalog vs Custom Specification
The EP-01-707 is available as a standard catalog item shipping in 3-5 days. If your application requires a non-standard ratio, shaft type, or mounting configuration, our engineering team offers custom designs with 4-6 week lead times. Minimum order quantities may apply.

🌾 Escenarios de aplicación típicos

🌾 Firebreak establishment and maintenance mowing

🚘 Disc mowing of grass and legume hay crops

🌱 Airfield perimeter and runway strip grass management

⛰ Sugar cane and crop stubble field mulching

🌳 Dairy farm laneway and yard surround maintenance

Planta de fabricación de Ever-power Australia Mower Gearbox Co., Ltd.

🛠 Guía de instalación y configuración

  1. After the first 10 hours of operation, re-torque all mounting bolts to specification and verify oil level. Perform the first oil drain and refill at 50 hours.
  2. Disconnect the tractor PTO shaft and safely support the mower implement on jack stands or blocks before beginning the gearbox installation procedure.
  3. For units weighing over 25 kg, use a chain hoist, engine crane, or two-person lift to position the gearbox. Never attempt to lift heavy gearboxes solo.
  4. Fill the gearbox with the recommended gear oil (SAE 80W-90 or 85W-140 EP) to the level indicated on the sight glass or dipstick. Do not overfill.
  5. Before operating at full load, run through a graduated break-in sequence: 30 minutes at half-throttle, then 30 minutes at three-quarter throttle, before engaging full PTO speed.
  6. Inspect the implement mounting pad for flatness using a straightedge. Any warping exceeding 0.5 mm should be corrected before the new gearbox is installed.
  7. Use Nord-Lock washers or thread-locking compound on all mounting bolts to prevent vibration-induced loosening during operation.

❓ Preguntas frecuentes

❓ How noisy is this gearbox during operation?

Our spiral bevel designs produce 72-78 dB(A) at 1 metre under rated load — significantly quieter than straight-bevel alternatives (typically 82-88 dB). Operators notice a meaningful reduction in gear whine.

❓ What is the difference between ratio options?

Ratio determines the speed/torque trade-off at the output. 1:1 maintains PTO speed (high blade RPM); 1:1.93 nearly halves output speed while doubling torque. Choose based on your target blade tip speed and vegetation density.

❓ What is the lead time for standard models?

In-stock standard models ship within 3-5 business days. For models requiring custom ratios or configurations, typical lead time is 4-6 weeks. Rush production is available for urgent requirements.

❓ How do I select the right gear ratio?

Match the ratio to your blade tip speed target. Lower ratios (e.g. 1:1) give higher blade RPM for finish mowing; higher ratios (e.g. 1:1.93 or above) trade speed for torque, ideal for thick brush. Calculate: output RPM = input RPM ÷ ratio.

❓ What is the expected operational lifespan?

With proper maintenance, our gearboxes typically deliver 3,000 to 5,000 operating hours. Many units in the field have exceeded 6,000 hours. Lifespan depends on operating load, maintenance compliance, and field conditions.

⭐ Opiniones de clientes e informes de campo

★★★★★

📍 Victoria, Australia

Buena relación calidad-precio. Nuestro equipo somete estas cajas de cambios a un uso intensivo y resisten mejor que las marcas anteriores que hemos probado.

★★★★★

📍 Iowa, United States

Hemos instalado seis de estos equipos en nuestra flota. Todas y cada una de las unidades han funcionado a la perfección durante dos temporadas completas de siega.

★★★★★

📍 Faisalabad, Pakistan

Excellent for orchard floor management. The cooling fin design makes maintenance easy and keeps unplanned downtime to a minimum.

★★★★☆

📍 Poltava, Ukraine

Runs noticeably cooler than the old gearbox it replaced. The improved cooling design and better oil volume are making a real difference.

★★★★☆

📍 Córdoba, Argentina

We tested this against a competitor unit side by side. This one runs quieter, stays cooler, and the oil stayed cleaner over 200 hours.

Gama de cajas de cambios agrícolas

⚖ EP-01-707 vs. Low-Cost Alternatives

Característica EP-01-707 (Ever-power) Alternativa genérica/de bajo costo
Drain Plug ✔ Magnetic Plug Captures Wear Particles ✘ Standard Plug, No Particle Capture
Traceability ✔ Laser-Etched Serial, Full Material Records ✘ No Serial Number, No Traceability
Housing Machining ✔ 5-Axis CNC, IT6 Bore Tolerance ✘ 3-Axis CNC or Manual, IT9 Bore Tolerance
Spare Parts Availability ✔ Full Inventory, Ships Within 24 Hours ✘ Limited Stock, 4-8 Week Back-Order
Lead Time ✔ 3-5 Days Standard, 4-6 Weeks Custom ✘ 8-12 Weeks, No Expedite Option
Gear Accuracy ✔ AGMA Class 8-10, CNC Ground Post Heat-Treatment ✘ AGMA Class 5-6, Hobbed Only, No Grinding
Oil Capacity ✔ Generous Sump for Extended Cooling, Sight Glass ✘ Minimal Oil Volume, No Level Indicator

🔄 Productos y accesorios relacionados

🏆 Certificaciones y estándares de calidad

Our manufacturing facility holds ISO 9001:2015 quality management and ISO 14001:2015 environmental management certifications. All gear steel is supplied with EN 10204 Type 3.1 mill test certificates. Heat treatment processes are monitored per CQI-9 (Special Process: Heat Treat System Assessment). Every EP-01-707 undergoes 100% dimensional inspection and functional testing before shipment.

🏭 ¿Por qué elegir Ever-power Australia Mower Gearbox Co.,Ltd.?

At Ever-power Australia Mower Gearbox Co.,Ltd., we have invested over two decades building one of the most advanced agricultural gearbox production facilities in the Asia-Pacific region. Our 19000 m² campus integrates in-house forging, CNC gear cutting, automated heat treatment, precision grinding, and assembly under one roof — giving us end-to-end quality control that outsourced manufacturers simply cannot match. We produce 59000 gearbox units annually, serving OEM partners and distributors across 49+ countries on six continents, with particular strength in the Australian, North American, and European markets.

eje de transmisión de la toma de fuerza

📞 Get Your EP-01-707 Quote Today

Ready to boost your mowing productivity with the EP-01-707? Our application engineers can match this gearbox to your specific tractor and implement — get a tailored recommendation today.

Solicitar presupuestoVer todos los productos

Productos relacionados