Caja de cambios para cortacésped EP-RC33

Caja de cambios para cortacésped EP-RC33

The EP-RC33 offers three switchable ratios (1:1.47, 1:1.69, 1:1.93) at 30 HP in a 26 kg housing. Property maintenance contractors and rural fire authorities choose the RC33 because it lets them adapt blade speed to changing vegetation — from fine lawn finish to thick seasonal grass and light scrub — with a single gearbox.

SKU: 633bf3c97512 Categoría: Etiquetas: , , , ,

Descripción


Built to Last: EP-RC33 Multi-Ratio Rotary Cutter Gearbox

El EP-RC33 Está diseñado para el operador que valora el tiempo de actividad por encima de todo. caja de cambios agrícola asas 30 / 30 / 30 HP Mediante engranajes cónicos espirales mecanizados con precisión, soportados por rodamientos de primera calidad y un sistema de sellado multietapa para una máxima vida útil.

EP-RC33 Multi-Ratio Rotary Cutter Gearbox

📈 EP-RC33 Technical Specifications

Parámetro Especificación
Número de modelo EP-RC33
Tipo de caja de cambios Multi-Ratio Rotary Cutter Gearbox
Relación(es) de transmisión 1:1.93 / 1:1.69 / 1:1.47
Configuración de los dientes 15/29, 13/22, 15/22
Módulo de engranajes 4.0 / 5.0 / 5.08
Potencia nominal 30 / 30 / 30 HP
Velocidad de entrada 540 rpm
Eje de entrada/salida 1 3/8 Z6 / Optic axis
Peso neto 26 Kg
Material de engranajes Acero aleado 20CrMnTi, carburizado y endurecido HRC 58-62
Material de vivienda Grey Cast Iron (HT200/HT250)
Protección de sellado Retenes de aceite multilabios NBR/FKM, con clasificación IP65+
Lubricación Aceite para engranajes SAE 80W-90 o 85W-140 EP
Tratamiento de superficies Imprimación electroforética + recubrimiento en polvo de poliéster, acabado rojo.

⭐ Características clave y ventajas de ingeniería

🚀

Redundant Lubrication Groove System

Machined oil distribution grooves in the housing bore supplement splash lubrication, providing a secondary oil path to bearings if sump level drops slightly below specification.

💪

Reinforced Grey Cast Iron Housing

HT250-grade grey iron casing with 14 mm wall thickness, ribbed for vibration damping and thermal dissipation, resisting cracking from rock strikes at mowing speed.

⚙

Standard 1 3/8″ 6-Spline PTO Input

Industry-standard input spline accepts all 540 RPM PTO shafts, ensuring bolt-on compatibility with tractors from 15 HP sub-compacts to 50 HP utility models.

⚗

Induction-Hardened Output Shaft

Output shaft journals hardened to HRC 50-55 via controlled induction heating, extending bearing seat life beyond 3,000 operating hours before re-machining is needed.

🔒

Triple-Stage Shaft Sealing

Inner labyrinth + double-lip FKM seal + external V-ring slinger form a three-barrier defense against water, mud, and fine dust penetrating to the bearing cavities.

⚡

Integrated External Cooling Fins

35% additional surface area from machined cooling ribs accelerates heat rejection, keeping oil temperature below 80 °C during sustained full-load summer mowing.

Caja de engranajes de segadora para uso agrícola

🔧 Compatibilidad de equipos y referencias cruzadas

🔄 Cross-Reference Compatibility for EP-RC33

The EP-RC33 is engineered as a direct replacement or upgrade for gearboxes fitted to equipment from leading manufacturers including:

McConnel • Fendt • Iseki • YTO • Massey Ferguson • Deutz-Fahr • Woods • Krone

Descargo de responsabilidad: Las marcas mencionadas anteriormente se utilizan únicamente para identificar la compatibilidad. Ever-power Australia Mower Gearbox Co., Ltd. no está afiliada, respaldada ni autorizada por ninguno de los fabricantes mencionados. Todas las marcas registradas pertenecen a sus respectivos propietarios.

📚 Guía de selección de cajas de cambios

The EP-RC33 covers a specific performance envelope. Use these selection criteria to verify it aligns with your operational parameters:

📌 Compatibilidad con el tipo de eje de salida
The EP-RC33 features 1 3/8 Z6 / Optic axis output. Verify your blade hub or implement rotor accepts this shaft type before ordering. We offer multiple output configurations — spline, taper, keyway, and flange — to match virtually any existing installation.
📌 Consideraciones sobre el peso y el montaje
At 26 Kg, the EP-RC33 is designed for compact and sub-compact tractor implements. Confirm your implement frame and three-point hitch can support this weight plus the weight of the blade assembly. Mounting bolt pattern and orientation should match your existing layout.
📌 Adaptación de la relación de engranajes a la velocidad de la punta de la cuchilla
For the EP-RC33 with ratio(s) 1:1.93 / 1:1.69 / 1:1.47, calculate your required blade tip speed: typically 4,500-5,500 m/min for standard rotary cutters, 3,000-4,000 m/min for heavy brush cutting, and 5,500-6,500 m/min for fine finish mowing. Output RPM = PTO RPM ÷ ratio. Multiply by blade diameter to get tip speed.
📌 Dimensionamiento de la potencia nominal en relación a la potencia de la toma de fuerza del tractor (HP)
The EP-RC33 is rated at 30 / 30 / 30 HP. Always select a gearbox rated at or above your tractor’s maximum PTO horsepower. For shock-load applications (mulching, brush clearing), add a 25-30% safety margin: a 60 HP tractor should use a 75+ HP rated gearbox.
📌 Selección de toma de fuerza (PTO) de 540 RPM frente a 1000 RPM
The EP-RC33 operates at 540 rpm. Most rotary mowers use 540 RPM PTO. The 1000 RPM standard is for larger implements on high-HP tractors. Never connect a 540 RPM gearbox to a 1000 RPM PTO — the doubled speed will destroy bearings and gears within minutes.

🌾 Escenarios de aplicación típicos

🌾 Mining site vegetation rehabilitation and control

🚘 Forestry site preparation and plantation row clearing

🌱 Stubble incorporation and green manure tillage

⛰ Municipal park and recreational reserve mowing

🌳 Silage paddock management and pasture renovation

Planta de fabricación de Ever-power Australia Mower Gearbox Co., Ltd.

🛠 Guía de instalación y configuración

  1. Before operating at full load, run through a graduated break-in sequence: 30 minutes at half-throttle, then 30 minutes at three-quarter throttle, before engaging full PTO speed.
  2. Inspect the implement mounting pad for flatness using a straightedge. Any warping exceeding 0.5 mm should be corrected before the new gearbox is installed.
  3. Use Nord-Lock washers or thread-locking compound on all mounting bolts to prevent vibration-induced loosening during operation.
  4. Haga funcionar la caja de cambios sin carga durante 5-10 minutos, luego apáguela y vuelva a comprobar el nivel de aceite; los sellos y cojinetes nuevos suelen absorber una pequeña cantidad de aceite inicial.
  5. Limpie a fondo la superficie de montaje del implemento, eliminando todo el óxido, los restos de juntas viejas, las escamas de pintura y los residuos que puedan impedir un contacto perfecto con la brida de la caja de engranajes.
  6. Coloque la caja de cambios sobre los espárragos de montaje o los orificios para los pernos, verificando que el eje de entrada esté orientado hacia la toma de fuerza del tractor y que el eje de salida esté alineado con el cubo de la cuchilla o el rotor.
  7. Asegúrese de que el eje de la toma de fuerza tenga una superposición de estrías de al menos 50% en todas las posiciones de funcionamiento. Una superposición insuficiente provoca un desgaste rápido de las estrías y una posible separación del eje.

❓ Preguntas frecuentes

❓ ¿Es seguro hacer funcionar esta caja de cambios a una velocidad de toma de fuerza de 1000 RPM?

Esta unidad está diseñada para funcionar a 540 RPM. Si se opera a 1000 RPM sin el engranaje adecuado, los cojinetes y engranajes se sobrecargarán, lo que provocará una falla rápida. Si necesita una configuración para 1000 RPM, comuníquese con nuestro equipo.

❓ ¿Puedo montar esta caja de cambios en ángulos no estándar?

La mayoría de los modelos están diseñados para salida vertical u horizontal, según se especifique. El montaje en ángulos inusuales puede afectar la distribución del aceite. Póngase en contacto con nuestro equipo de ingeniería para confirmar la idoneidad antes de instalarlo en una orientación no estándar.

❓ How do I identify when my gearbox needs repair?

Warning signs: unusual grinding or whining noise, increased vibration, oil leakage, metallic particles on the magnetic drain plug, elevated operating temperature, or detectable play in the output shaft.

❓ Can I visit your manufacturing facility?

We welcome factory visits and audits from prospective partners. Our production facility is equipped for full tours, and we can arrange local transport from the nearest airport. Contact us to schedule a convenient date.

❓ What is the recommended oil change schedule?

Drain and replace oil after the first 50 hours of break-in. After that, change oil every 200-300 hours or at least once per season. Always drain warm oil for complete evacuation and inspect the magnetic drain plug for metallic debris.

⭐ Opiniones de clientes e informes de campo

★★★★★

📍 Tasmania, Australia

First purchase from this manufacturer and I am thoroughly impressed. Build quality, documentation, and support were all top-notch.

★★★★★

📍 Konya, Turkey

After comparing specifications across five brands, this offered the best combination of materials, weight, and price. No regrets.

★★★★★

📍 Iowa, United States

Fitted to my finish mower last season. Over 400 hours and counting — zero leaks, minimal noise. Excellent value for a professional-grade unit.

★★★★☆

📍 Faisalabad, Pakistan

Running it on a 40-50 HP tractor through rocky paddocks. Handles rocks and rough ground without complaint. Very impressed with the build.

★★★★☆

📍 Poltava, Ukraine

Purchased two units for our operation. Consistent quality between both units, which tells me their factory QC is solid. Will buy again.

Gama de cajas de cambios agrícolas

⚖ EP-RC33 vs. Low-Cost Alternatives

Característica EP-RC33 (Ever-power) Alternativa genérica/de bajo costo
Lead Time ✔ 3-5 Days Standard, 4-6 Weeks Custom ✘ 8-12 Weeks, No Expedite Option
Gear Accuracy ✔ AGMA Class 8-10, CNC Ground Post Heat-Treatment ✘ AGMA Class 5-6, Hobbed Only, No Grinding
Oil Capacity ✔ Generous Sump for Extended Cooling, Sight Glass ✘ Minimal Oil Volume, No Level Indicator
Drain Plug ✔ Magnetic Plug Captures Wear Particles ✘ Standard Plug, No Particle Capture
Traceability ✔ Laser-Etched Serial, Full Material Records ✘ No Serial Number, No Traceability
Housing Machining ✔ 5-Axis CNC, IT6 Bore Tolerance ✘ 3-Axis CNC or Manual, IT9 Bore Tolerance
Spare Parts Availability ✔ Full Inventory, Ships Within 24 Hours ✘ Limited Stock, 4-8 Week Back-Order

🔄 Productos y accesorios relacionados

🏆 Certificaciones y estándares de calidad

Manufactured under ISO 9001:2015 and audited annually by international OEM customers, the EP-RC33 represents our commitment to world-class quality. Gear material certificates (3.1), heat-treatment records, bearing lot traceability, and final inspection reports are maintained for every production batch and available upon customer request.

🏭 ¿Por qué elegir Ever-power Australia Mower Gearbox Co.,Ltd.?

At Ever-power Australia Mower Gearbox Co.,Ltd., we are not just a gearbox factory — we are a full-service power transmission partner. From initial application engineering and 3D prototype modelling through to volume production, global logistics, and after-sales technical support, we manage the complete product lifecycle. Our 29000 m² facility in China is audited annually by international OEM customers and consistently rated among the top-tier suppliers in the agricultural transmission sector.

eje de transmisión de la toma de fuerza

📞 Get Your EP-RC33 Quote Today

Need the EP-RC33 shipped fast? In-stock standard models dispatch within 3-5 business days. Contact us now to confirm availability and lock in today’s pricing before your next mowing season.

Solicitar presupuestoVer todos los productos

Productos relacionados