توضیحات محصول
| Product Features | Description |
| Product Models | T2, T4, T6, T7, T8, T10, T12, T16, T20, T25, Z2, Z4, Z6, Z7, Z8, Z10, Z12, Z16, Z20, Z25, JRTM2, JRTM4, JRTM6, JRTM7, JRTM8, JRTM10, JRTM12, JRTM16, JRTM20, JRTM25 |
| Maintenance | Clean internally and replace lubricant after initial use of 2 weeks or 100-200 hours. For long-term use, replace lubricant every half to 1 year or every 1000-2000 hours |
| Lubricant | China Petroleum’s all-effect gear oil of 90-120 degrees. Under low speed and light load conditions, it is recommended to use all-effect gear oil of 90 degrees. Under heavy load and high temperature conditions, it is recommended to use all-effect gear oil of 120 degrees |
| توضیحات محصول | The T series spiral bevel gear steering gearbox is widely used in food, pharmaceutical, chemical, steel, metallurgy, textile, plastic, paper and other machinery equipment, assembly lines and other industries |
| Technical Features | The gearbox has a high rigidity FC-25 cast iron casing. The gears are made of high-quality high-purity alloy steel 20CrMnTi carburized and quenched, and ground. The shaft is tempered alloy steel with high load-bearing capacity. It is equipped with a heavy load-bearing tapered roller bearing. The oil seal has a double lip seal, which has dustproof and oil leakage prevention capabilities |
| Performance Features | The T series spiral bevel gear steering gearbox is standardized and has many varieties. The speed ratio is all actual transmission ratios, with an average efficiency of 98%. It can run CHINAMFG and reverse, with smooth low-speed or high-speed transmission, low noise, small vibration, and large bearing force |
| Technical Parameters | Speed ratio range: 1/1, 1.5/1, 2/1, 2.5/1, 3/1, 4/1, 5/1. Torque range: 11.2 – 5713 Nm. Power range: 0.014 – 335 kW |
·Product Models: T2, T4, T6, T7, T8, T10, T12, T16, T20, T25, Z2, Z4, Z6, Z7, Z8, Z10, Z12, Z16, Z20, Z25, JRTM2, JRTM4, JRTM6, JRTM7, JRTM8, JRTM10, JRTM12, JRTM16, JRTM20, JRTM25.
·Maintenance: The gearbox should be cleaned internally and the lubricant should be replaced after the initial use of 2 weeks or 100-200 hours. For long-term use, the lubricant should be replaced every half to 1 year or every 1000-2000 hours.
·Lubricant: The product uses China Petroleum’s all-effect gear oil of 90-120 degrees. Under low speed and light load conditions, it is recommended to use all-effect gear oil of 90 degrees. Under heavy load and high temperature conditions, it is recommended to use all-effect gear oil of 120 degrees.
·Product Description: The T series spiral bevel gear steering gearbox is widely used in food, pharmaceutical, chemical, steel, metallurgy, textile, plastic, paper and other machinery equipment, assembly lines and other industries.
·Technical Features: The gearbox has a high rigidity FC-25 cast iron casing. The gears are made of high-quality high-purity alloy steel 20CrMnTi carburized and quenched, and ground. The shaft is tempered alloy steel with high load-bearing capacity. It is equipped with a heavy load-bearing tapered roller bearing. The oil seal has a double lip seal, which has dustproof and oil leakage prevention capabilities.
·Performance Features: The T series spiral bevel gear steering gearbox is standardized and has many varieties. The speed ratio is all actual transmission ratios, with an average efficiency of 98%. It can run CHINAMFG and reverse, with smooth low-speed or high-speed transmission, low noise, small vibration, and large bearing force.
RFQ
Q:What information should I tell you to confirm speed reducer?
A: Model/Size, Transmission Ratio, Shaft directions & Order quantity.
Q:What if I don’t know which gear reducer I need?
A:Don’t worry, Send as much information as you can, our team will help you find the right 1 you are looking for.
Q:What should I provide if I want to order NON-STANDERD speed reducers?
A: Drafts, Dimensions, Pictures and samples if possible.
Q:What is the MOQ?
A: It is OK for 1 or small pieces trial order for quality testing.
Q:How long should I wait for the feedback after I send the inquiry?
A: Within 6 hours
Q:What is the payment term?
A:You can pay via T/T(30% in advance+70% before delivery), L/C ,West Union etc
| کاربرد: | Motor, Electric Cars, Motorcycle, Machinery, Marine, Toy, Agricultural Machinery, Car |
|---|---|
| عملکرد: | Distribution Power, Clutch, Change Drive Torque, Change Drive Direction, Speed Changing, Speed Reduction, Speed Increase |
| طرح بندی: | کواکسیال |
| سختی: | سطح دندانه سخت شده |
| نصب: | Horizontal Type |
| مرحله: | Three-Step |
| Samples: |
US$ 100/Piece
1 Piece(Min.Order) | |
|---|
Adjusting Tension on a Mower Gearbox Belt
Proper tension adjustment of the gearbox belt in your mower is crucial for optimal performance and belt longevity. Follow these steps to adjust the tension:
- Preparation: Turn off the mower’s engine and disconnect the spark plug wire to ensure safety.
- Locate the Adjustment Mechanism: Identify the tension adjustment mechanism on the mower. This could be a tensioning bolt, an adjustable bracket, or another mechanism depending on the mower model.
- Loosen Bolts: If your mower has tensioning bolts, slightly loosen the mounting bolts securing the gearbox in place. This allows the gearbox to move and adjust tension.
- Adjust Tension: Use the tension adjustment mechanism to increase or decrease the tension on the belt. Refer to your mower’s manual for recommended tension specifications.
- Check Tension: After adjusting, check the tension by pressing down on the belt at a midpoint between the pulleys. The belt should give a little, but not excessively. Also, check for proper alignment of the pulleys.
- Tighten Bolts: Once the tension is set correctly, tighten the mounting bolts of the gearbox to secure it in place.
- Test Operation: Reconnect the spark plug wire and start the mower to observe the belt’s operation. Listen for any unusual noises and monitor the belt for proper engagement with the pulleys.
Regularly checking and adjusting the tension of the gearbox belt ensures efficient power transmission and prevents premature wear. If you’re unsure about the proper tension adjustment, consult your mower’s manual or seek assistance from a professional.
Lifespan of a Typical Mower Gearbox
The lifespan of a mower gearbox can vary depending on several factors, including the quality of the gearbox, maintenance practices, usage frequency, and operating conditions. On average, a well-maintained and high-quality mower gearbox can last between 5 to 10 years or even more.
Regular maintenance, such as checking and maintaining the oil level, cleaning and lubricating components, and addressing any issues promptly, can significantly extend the lifespan of a mower gearbox. Quality components, proper usage, and adherence to manufacturer guidelines also play a crucial role in determining how long a mower gearbox will last.
If you start noticing signs of wear, performance issues, or unusual noises from the gearbox, it’s important to address them promptly to prevent further damage and potentially extend the gearbox’s lifespan.
عملکرد گیربکس ماشین چمن زنی
گیربکس ماشین چمنزنی از طریق مجموعهای از چرخدندهها و اجزایی که با هم کار میکنند تا قدرت را منتقل کرده و حرکت چرخشی موتور را به عمل برش تیغهها تبدیل کنند، عمل میکند. در اینجا نحوه عملکرد یک گیربکس معمولی ماشین چمنزنی آورده شده است:
- ورودی برق: گیربکس ماشین چمن زنی، نیرو را از طریق یک شفت محرک از موتور ماشین چمن زنی دریافت می کند.
- کاهش دنده: گیربکس شامل مجموعهای از چرخدندهها است که با نسبتهای مشخصی چیده شدهاند تا به گشتاور و تبدیل سرعت مورد نیاز دست یابند. چرخدنده ورودی که به شفت محرک متصل است، با یک یا چند چرخدنده میانی درگیر میشود.
- تبدیل گشتاور: با چرخش چرخدنده ورودی، چرخدندههای میانی نیز به حرکت در میآیند. چیدمان چرخدندهها در گیربکس منجر به کاهش سرعت و افزایش گشتاور میشود. این امر برای تأمین نیروی لازم برای برش پوشش گیاهی توسط تیغههای برش ضروری است.
- اتصال تیغه: شفت خروجی گیربکس به تیغههای برش متصل است. با چرخش شفت خروجی گیربکس، گشتاور به تیغهها منتقل میشود و باعث چرخش آنها میگردد.
- چرخش تیغه: حرکت چرخشی تیغهها همان چیزی است که آنها را قادر میسازد تا چمن و سایر پوششهای گیاهی را برش دهند. گشتاور افزایش یافته تولید شده توسط گیربکس به تیغهها اجازه میدهد تا به طور مؤثر اقدامات برش یا مالچپاشی را انجام دهند.
گیربکسهای ماشین چمنزنی مدرن برای کارایی، دوام و دقت طراحی شدهاند. آنها اغلب مجهز به بلبرینگ، آببند و روانکاری هستند تا اصطکاک را به حداقل برسانند و عملکرد روان را تضمین کنند. برخی از گیربکسهای ماشین چمنزنی همچنین شامل ویژگیهای اضافی مانند ارتفاع برش قابل تنظیم، هماهنگسازی تیغه و کنترل جهت برای افزایش تطبیقپذیری ماشین چمنزنی هستند.
editor by CX 2023-10-07
