توضیحات محصول
| Product Features | Description |
| Product Models | T2, T4, T6, T7, T8, T10, T12, T16, T20, T25, Z2, Z4, Z6, Z7, Z8, Z10, Z12, Z16, Z20, Z25, JRTM2, JRTM4, JRTM6, JRTM7, JRTM8, JRTM10, JRTM12, JRTM16, JRTM20, JRTM25 |
| Maintenance | Clean internally and replace lubricant after initial use of 2 weeks or 100-200 hours. For long-term use, replace lubricant every half to 1 year or every 1000-2000 hours |
| Lubricant | China Petroleum’s all-effect gear oil of 90-120 degrees. Under low speed and light load conditions, it is recommended to use all-effect gear oil of 90 degrees. Under heavy load and high temperature conditions, it is recommended to use all-effect gear oil of 120 degrees |
| توضیحات محصول | The T series spiral bevel gear steering gearbox is widely used in food, pharmaceutical, chemical, steel, metallurgy, textile, plastic, paper and other machinery equipment, assembly lines and other industries |
| Technical Features | The gearbox has a high rigidity FC-25 cast iron casing. The gears are made of high-quality high-purity alloy steel 20CrMnTi carburized and quenched, and ground. The shaft is tempered alloy steel with high load-bearing capacity. It is equipped with a heavy load-bearing tapered roller bearing. The oil seal has a double lip seal, which has dustproof and oil leakage prevention capabilities |
| Performance Features | The T series spiral bevel gear steering gearbox is standardized and has many varieties. The speed ratio is all actual transmission ratios, with an average efficiency of 98%. It can run CHINAMFG and reverse, with smooth low-speed or high-speed transmission, low noise, small vibration, and large bearing force |
| Technical Parameters | Speed ratio range: 1/1, 1.5/1, 2/1, 2.5/1, 3/1, 4/1, 5/1. Torque range: 11.2 – 5713 Nm. Power range: 0.014 – 335 kW |
·Product Models: T2, T4, T6, T7, T8, T10, T12, T16, T20, T25, Z2, Z4, Z6, Z7, Z8, Z10, Z12, Z16, Z20, Z25, JRTM2, JRTM4, JRTM6, JRTM7, JRTM8, JRTM10, JRTM12, JRTM16, JRTM20, JRTM25.
·Maintenance: The gearbox should be cleaned internally and the lubricant should be replaced after the initial use of 2 weeks or 100-200 hours. For long-term use, the lubricant should be replaced every half to 1 year or every 1000-2000 hours.
·Lubricant: The product uses China Petroleum’s all-effect gear oil of 90-120 degrees. Under low speed and light load conditions, it is recommended to use all-effect gear oil of 90 degrees. Under heavy load and high temperature conditions, it is recommended to use all-effect gear oil of 120 degrees.
·Product Description: The T series spiral bevel gear steering gearbox is widely used in food, pharmaceutical, chemical, steel, metallurgy, textile, plastic, paper and other machinery equipment, assembly lines and other industries.
·Technical Features: The gearbox has a high rigidity FC-25 cast iron casing. The gears are made of high-quality high-purity alloy steel 20CrMnTi carburized and quenched, and ground. The shaft is tempered alloy steel with high load-bearing capacity. It is equipped with a heavy load-bearing tapered roller bearing. The oil seal has a double lip seal, which has dustproof and oil leakage prevention capabilities.
·Performance Features: The T series spiral bevel gear steering gearbox is standardized and has many varieties. The speed ratio is all actual transmission ratios, with an average efficiency of 98%. It can run CHINAMFG and reverse, with smooth low-speed or high-speed transmission, low noise, small vibration, and large bearing force.
RFQ
Q:What information should I tell you to confirm speed reducer?
A: Model/Size, Transmission Ratio, Shaft directions & Order quantity.
Q:What if I don’t know which gear reducer I need?
A:Don’t worry, Send as much information as you can, our team will help you find the right 1 you are looking for.
Q:What should I provide if I want to order NON-STANDERD speed reducers?
A: Drafts, Dimensions, Pictures and samples if possible.
Q:What is the MOQ?
A: It is OK for 1 or small pieces trial order for quality testing.
Q:How long should I wait for the feedback after I send the inquiry?
A: Within 6 hours
Q:What is the payment term?
A:You can pay via T/T(30% in advance+70% before delivery), L/C ,West Union etc
| کاربرد: | Motor, Electric Cars, Motorcycle, Machinery, Marine, Toy, Agricultural Machinery, Car |
|---|---|
| عملکرد: | Distribution Power, Clutch, Change Drive Torque, Change Drive Direction, Speed Changing, Speed Reduction, Speed Increase |
| طرح بندی: | کواکسیال |
| سختی: | سطح دندانه سخت شده |
| نصب: | Horizontal Type |
| مرحله: | Three-Step |
| Samples: |
US$ 100/Piece
1 Piece(Min.Order) | |
|---|
Repair or Replacement of a Mower Gearbox
Whether a mower gearbox can be repaired or needs to be replaced depends on the extent of the damage and the condition of the gearbox components. Here are some factors to consider:
- Minor Issues: If the gearbox is experiencing minor issues such as a leaking seal, damaged gasket, or a loose bolt, these problems can often be repaired without the need for a full replacement.
- Worn Gears or Bearings: If the gears or bearings are worn or damaged, they can sometimes be replaced individually, especially if the rest of the gearbox is in good condition.
- Severe Damage: If the gearbox housing is cracked, the gears are severely damaged, or the entire unit is extensively worn, a replacement gearbox might be the more cost-effective solution.
- Cost of Repairs: Sometimes, the cost of repairing multiple components in a gearbox can be close to the cost of a new gearbox. In such cases, it might make more sense to opt for a replacement.
- Age of the Mower: If the mower itself is old and the gearbox is showing signs of wear, it might be worth considering whether it’s more economical to invest in a new mower with a new gearbox.
It’s recommended to consult a professional mechanic or technician who specializes in mower repairs. They can assess the extent of the damage, provide you with repair and replacement options, and help you make an informed decision based on the specific situation.
Lifespan of a Typical Mower Gearbox
The lifespan of a mower gearbox can vary depending on several factors, including the quality of the gearbox, maintenance practices, usage frequency, and operating conditions. On average, a well-maintained and high-quality mower gearbox can last between 5 to 10 years or even more.
Regular maintenance, such as checking and maintaining the oil level, cleaning and lubricating components, and addressing any issues promptly, can significantly extend the lifespan of a mower gearbox. Quality components, proper usage, and adherence to manufacturer guidelines also play a crucial role in determining how long a mower gearbox will last.
If you start noticing signs of wear, performance issues, or unusual noises from the gearbox, it’s important to address them promptly to prevent further damage and potentially extend the gearbox’s lifespan.
عملکرد گیربکس ماشین چمن زنی
گیربکس ماشین چمنزنی از طریق مجموعهای از چرخدندهها و اجزایی که با هم کار میکنند تا قدرت را منتقل کرده و حرکت چرخشی موتور را به عمل برش تیغهها تبدیل کنند، عمل میکند. در اینجا نحوه عملکرد یک گیربکس معمولی ماشین چمنزنی آورده شده است:
- ورودی برق: گیربکس ماشین چمن زنی، نیرو را از طریق یک شفت محرک از موتور ماشین چمن زنی دریافت می کند.
- کاهش دنده: گیربکس شامل مجموعهای از چرخدندهها است که با نسبتهای مشخصی چیده شدهاند تا به گشتاور و تبدیل سرعت مورد نیاز دست یابند. چرخدنده ورودی که به شفت محرک متصل است، با یک یا چند چرخدنده میانی درگیر میشود.
- تبدیل گشتاور: با چرخش چرخدنده ورودی، چرخدندههای میانی نیز به حرکت در میآیند. چیدمان چرخدندهها در گیربکس منجر به کاهش سرعت و افزایش گشتاور میشود. این امر برای تأمین نیروی لازم برای برش پوشش گیاهی توسط تیغههای برش ضروری است.
- اتصال تیغه: شفت خروجی گیربکس به تیغههای برش متصل است. با چرخش شفت خروجی گیربکس، گشتاور به تیغهها منتقل میشود و باعث چرخش آنها میگردد.
- چرخش تیغه: حرکت چرخشی تیغهها همان چیزی است که آنها را قادر میسازد تا چمن و سایر پوششهای گیاهی را برش دهند. گشتاور افزایش یافته تولید شده توسط گیربکس به تیغهها اجازه میدهد تا به طور مؤثر اقدامات برش یا مالچپاشی را انجام دهند.
گیربکسهای ماشین چمنزنی مدرن برای کارایی، دوام و دقت طراحی شدهاند. آنها اغلب مجهز به بلبرینگ، آببند و روانکاری هستند تا اصطکاک را به حداقل برسانند و عملکرد روان را تضمین کنند. برخی از گیربکسهای ماشین چمنزنی همچنین شامل ویژگیهای اضافی مانند ارتفاع برش قابل تنظیم، هماهنگسازی تیغه و کنترل جهت برای افزایش تطبیقپذیری ماشین چمنزنی هستند.
editor by CX 2023-09-22
