Gearbox for Combined Tillage

How: Refer to your combined tillage machine manufacturer’s manual for the recommended multi-shaft output operating speed

Why it matters: Together with PTO speed, this defines the exact gear ratio your gearbox needs

How: Assess exposure to dust, moisture, chemicals, and temperature extremes in your typical multi-function tillage conditions

Why it matters: Determines the appropriate seal grade, surface coating, and housing material specification

How: Estimate your annual operating hours for the combined tillage machine to determine appropriate service life rating

Why it matters: 장시간 가동 작업에는 시간당 최저 비용을 위해 프리미엄 베어링 및 기어 사양을 적용하는 것이 타당합니다.

How: Determine whether the multi-shaft output on your combined tillage machine requires clockwise or counter-clockwise output when viewed from the drive end

Why it matters: Incorrect rotation direction will damage the implement or produce no useful work

How: Measure the bolt hole positions, centre distances, and overall envelope on your combined tillage machine’s gearbox mounting flange

Why it matters: Ensures direct bolt-on installation without any fabrication or adapter plates

How: Calculate the peak torque your multi-function tillage application generates — including shock loads from obstacles or material variations

Why it matters: The gearbox must handle peak torque without activating overload protection during normal operation

How: Identify the coupling type on your combined tillage machine — keyed, splined, flanged, or hollow bore

Why it matters: 출력이 일치하지 않으면 비용이 많이 드는 어댑터 커플링이 필요하며 잠재적인 고장 지점이 발생할 수 있습니다.

Remove the fill plug and slowly add the recommended gear oil until it reaches the level indicator. Use the lubricant grade specified in the gearbox documentation (typically SAE 80W-90 GL-5 or equivalent). Replace the fill plug and hand-tighten, then snug with a wrench. Verify the breather cap is clean and unobstructed.

Carefully lift the new Combined Tillage gearbox into position on the mounting flange, aligning all bolt holes. Insert mounting bolts hand-tight first, confirming proper alignment. Once all bolts are started, torque them in a star (cross) pattern to the value specified in the installation manual. Verify the gearbox sits flush against the frame with no gaps.

Disconnect the PTO driveline from the gearbox input shaft. Support the gearbox weight with a floor jack or overhead hoist (typical weight: 15-70 kg depending on model). Remove all mounting bolts in a criss-cross pattern to relieve clamping stress evenly. Carefully lower the old gearbox and set it aside.

Attach the gearbox output shaft to the combined tillage machine’s multi-shaft output drive coupling. For keyed connections, align the keyway and slide the coupling on, then secure with the retaining bolt and torque to specification. For splined outputs, apply anti-seize to the splines and verify full engagement before locking.

Start the tractor and engage the PTO at low RPM (approximately 300 RPM). Listen carefully for any grinding, whining, knocking, or clicking sounds. Run at low speed for 15-20 minutes, monitoring the gearbox housing temperature by hand (carefully). Check for oil leaks at all seals and the mounting interface. Gradually increase to full operating speed.

Clean the mounting flange on the combined tillage machine frame with a wire brush and solvent, removing all old sealant, rust, and debris. Inspect the mounting surface for cracks, stripped threads, or warping. Chase any damaged bolt threads with a tap. Apply a thin film of anti-seize compound to the mounting face if specified.

Locate the drain plug on the existing gearbox and position a catch container underneath. Remove the drain plug and allow all oil to drain completely — inspect the oil for metal particles or discolouration that may indicate internal wear. Record the old gearbox model number, mounting bolt size, and shaft dimensions for reference.

Probable Cause: Insufficient lubricant or incorrect oil grade

Recommended Action: Drain and inspect oil for metal particles. Refill with correct grade. If noise persists after oil change, bearing or gear inspection is required. Contact support for rebuild guidance.

Probable Cause: Overfilled oil level creating excess internal pressure

Recommended Action: First, check and correct the oil level — overfilling is a surprisingly common cause of seal leaks. Clean or replace the breather cap. If oil level is correct and breather is clear, the seal has worn and should be replaced using our seal kit.

Probable Cause: Stripped gear teeth or broken gear

Recommended Action: Check the overload protection device first — this is the most likely cause if the gearbox was recently subjected to a sudden overload. Replace the shear bolt or reset the slip clutch per the manual. If overload protection is intact, the gearbox has internal damage and requires professional service.

Probable Cause: Worn universal joints in the driveline

Recommended Action: First check all mounting bolt torques — vibration frequently loosens fasteners, which then amplifies the vibration. Next, inspect the PTO driveline U-joints for wear or binding. Verify driveline angles are within specification. Finally, check the output coupling to the multi-shaft output for wear or damage.

Probable Cause: Loose internal components or retaining hardware

Recommended Action: A clunking sound specifically on PTO engagement (but not during operation) usually indicates driveline lash — check driveline telescoping tube for wear. If the clunk occurs during operation, it may indicate excessive gear backlash from internal wear. Have the gearbox inspected if the sound is progressive.

Absolutely. We manufacture gearboxes with keyed, splined, flanged, hex, and hollow-bore output shaft configurations. If your combined tillage machine requires a non-standard output size, spline count, or connection type, our engineering team will design and machine it to your exact specifications at no additional lead time for common modifications.

Each gearbox is drained of shipping oil, wrapped in VCI (Vapor Corrosion Inhibitor) film, and crated in a sturdy plywood box rated for international freight. This packaging protects against moisture, impact, and corrosion during transit — even for shipments to remote Australian properties via road freight.

Our 24-month comprehensive warranty covers all defects in materials and workmanship, including bearings, gears, seals, and housing. It applies from the date of purchase and is backed by our ISO-certified quality management system. Extended warranty programs are available for bulk and fleet orders.

We maintain compatibility databases covering combined tillage machine models from the past 25+ years. Most older models can be directly fitted with our current gearbox range. For discontinued or rare models, send us the mounting dimensions and shaft specifications, and we will confirm fitment or design a custom adapter.

Provide us with your tractor brand/model and PTO speed, the combined tillage machine manufacturer and model, and the old gearbox part number if available. Alternatively, measure the input/output shaft dimensions and mounting bolt pattern. Our selection engineers will identify the correct match, typically within 24 hours.

Every gearbox ships with: installation manual with torque specifications, lubrication and maintenance schedule, parts diagram with individual part numbers, warranty registration card, and a quality inspection certificate with the unit’s serial number and test results.

We offer tiered pricing starting from single-unit purchases, with meaningful discounts beginning at 5+ units. Dealer and OEM pricing structures are available for agricultural equipment retailers and combined tillage machine manufacturers. Contact our sales team for a formal quotation tailored to your volume requirements.

Routine service (oil changes, seal replacement, bearing inspection) can be performed on-site with standard tools. For major rebuilds, we supply complete overhaul kits containing all bearings, seals, and gaskets. Detailed service manuals and video guides are available for download from our support portal.

Yes — every purchase includes access to our engineering support team for installation guidance, troubleshooting, maintenance advice, and parts ordering. Support is available via phone, email, and our online contact form. There is no charge for technical support during or after the warranty period.

We offer a comprehensive range of ratios from 1:1 through 1:6 to match virtually any combined tillage machine configuration. Standard catalogue ratios ship within days; custom ratios can be manufactured within 2-3 weeks. Our engineers will recommend the optimal ratio based on your tractor PTO speed and multi-function tillage requirements.