Kotak Gear Pemotong Rumput EP-RC61T

Kotak Gear Pemotong Rumput EP-RC61T

With four selectable ratios (1:1 to 1:1.93) and 60 HP capacity, the EP-RC61T is designed for operators who run multiple implement types from one tractor. Custom harvesters and agri-service businesses reduce downtime and inventory by keeping a single EP-RC61T on hand instead of stocking four separate gearboxes.

SKU: 8d0a1d9f788f Kategori: Teg: , , , ,

Penerangan


EP-RC61T โ€” Professional-Grade Multi-Ratio Rotary Cutter Gearbox for Agricultural Mowing

The EP-RC61T is a purpose-engineered lawn mower gearbox delivering reliable right-angle power transmission at 60 HP with 540 rpm PTO input. Its spiral bevel gears and sealed construction ensure consistent performance across thousands of operating hours in demanding field conditions.

EP-RC61T Multi-Ratio Rotary Cutter Gearbox

📈 EP-RC61T Technical Specifications

Parameter Spesifikasi
Nombor Model EP-RC61T
Jenis Kotak Gear Multi-Ratio Rotary Cutter Gearbox
Nisbah Gear 1:1 / 1:1.21 / 1:1.46 / 1:1.93
Konfigurasi Gigi 16/16, 17/14, 19/13, 27/14
Modul Gear 7.0 / 7.0 / 7.0 / 5.5
Kuasa Dinilai 60 HP
Kelajuan Input 540 rpm
Aci Input/Output 1 3/8 Z6 / 1 3/8 Z6
Berat Bersih 33.5 Kg
Bahan Gear Keluli Aloi 20CrMnTi, Dikarburisasi & Diperkeras HRC 58-62
Bahan Perumahan Grey Cast Iron (HT200/HT250)
Perlindungan Meterai Meterai Minyak NBR/FKM Berbilang Bibir, Dinilai IP65+
Pelinciran Minyak Gear SAE 80W-90 atau 85W-140 EP
Rawatan Permukaan Primer E-Coat + Salutan Serbuk Poliester, Kemasan Merah

โญ Ciri-ciri Utama & Kelebihan Kejuruteraan

⚖

Tip-Relief Quiet Gear Profile

Tooth profile modifications (tip relief + lead crowning) reduce gear-mesh noise by 6 dB versus standard straight bevel designs, improving operator comfort.

🚀

Abrasion-Resistant Cast Housing

Extra-thick grey iron walls with hardened mounting faces, resisting the abrasive wear caused by constant soil contact during deep tillage operations.

💪

Bolt-On Precision Flange Mount

Machined flange with dowel pin locations for accurate, repeatable tiller frame alignment, eliminating vibration-inducing misalignment during extended tillage runs.

⚙

Gear-Ground Tooth Flanks, Ra 0.5 ฮผm

Post-heat-treatment gear grinding achieves consistent surface finish and AGMA Class 9 geometry, reducing running-in wear and extending time to first service.

⚗

Hardened Dowel-Pin Alignment

Two precision ground dowel pins locate the housing halves within 0.02 mm, guaranteeing gear centre distance accuracy and eliminating assembly-induced backlash.

🔒

Zinc Flake Anti-Corrosion Fasteners

All external bolts finished with zinc-flake coating (Delta-Protekt) rated for 720 hours of salt spray, preventing seized fasteners during later disassembly.

Kotak gear pemotong rumput dalam kegunaan pertanian

๐Ÿ”ง Keserasian & Rujukan Silang Peralatan

🔄 Cross-Reference Compatibility for EP-RC61T

The EP-RC61T is engineered as a direct replacement or upgrade for gearboxes fitted to equipment from leading manufacturers including:

Bomford • Valtra • Yanmar • Lovol • New Holland • Bush Hog • Kioti • Vicon

Penafian: Nama jenama di atas dirujuk semata-mata untuk pengenalpastian keserasian. Ever-power Australia Mower Gearbox Co.,Ltd. tidak bergabung dengan, disokong oleh atau dibenarkan oleh mana-mana pengeluar tersenarai. Semua tanda dagangan adalah milik pemilik masing-masing.

๐Ÿ“š Panduan Pemilihan Kotak Gear

Choosing the right mower gearbox is critical for implement performance and longevity. Use the following criteria when evaluating the EP-RC61T:

📌 Matching Gear Ratio to Blade Tip Speed
For the EP-RC61T with ratio(s) 1:1 / 1:1.21 / 1:1.46 / 1:1.93, calculate your required blade tip speed: typically 4,500-5,500 m/min for standard rotary cutters, 3,000-4,000 m/min for heavy brush cutting, and 5,500-6,500 m/min for fine finish mowing. Output RPM = PTO RPM รท ratio. Multiply by blade diameter to get tip speed.
📌 Sizing Power Rating to Tractor PTO HP
The EP-RC61T is rated at 60 HP. Always select a gearbox rated at or above your tractor’s maximum PTO horsepower. For shock-load applications (mulching, brush clearing), add a 25-30% safety margin: a 60 HP tractor should use a 75+ HP rated gearbox.
๐Ÿ“Œ Pilihan PTO 540 RPM vs 1000 RPM
The EP-RC61T operates at 540 rpm. Most rotary mowers use 540 RPM PTO. The 1000 RPM standard is for larger implements on high-HP tractors. Never connect a 540 RPM gearbox to a 1000 RPM PTO โ€” the doubled speed will destroy bearings and gears within minutes.
๐Ÿ“Œ Perumah Besi Tuang vs Perumah Aluminium
The EP-RC61T uses a grey cast iron housing. Cast iron excels in vibration damping, impact resistance, and heat dissipation โ€” ideal for rough, rocky mowing conditions. Aluminium is lighter and more corrosion-resistant, better suited to wet environments and weight-sensitive implements.
๐Ÿ“Œ Katalog Standard vs Spesifikasi Tersuai
The EP-RC61T is available as a standard catalog item shipping in 3-5 days. If your application requires a non-standard ratio, shaft type, or mounting configuration, our engineering team offers custom designs with 4-6 week lead times. Minimum order quantities may apply.

๐ŸŒพ Senario Aplikasi Lazim

🌾 Disc mowing of grass and legume hay crops

🚘 Airfield perimeter and runway strip grass management

🌱 Sugar cane and crop stubble field mulching

⛰ Dairy farm laneway and yard surround maintenance

🌳 Conservation tillage and minimum-disturbance cultivation

Kemudahan pengeluaran Ever-power Australia Mower Gearbox Co.,Ltd.

๐Ÿ›  Panduan Pemasangan & Persediaan

  1. Inspect the implement mounting pad for flatness using a straightedge. Any warping exceeding 0.5 mm should be corrected before the new gearbox is installed.
  2. Use Nord-Lock washers or thread-locking compound on all mounting bolts to prevent vibration-induced loosening during operation.
  3. Run the gearbox at no load for 5-10 minutes, then shut down and re-check oil level โ€” new seals and bearings often absorb a small amount of initial oil.
  4. Clean the implement mounting surface thoroughly, removing all rust, old gasket material, paint flakes, and debris that could prevent flush contact with the gearbox flange.
  5. Position the gearbox onto the mounting studs or bolt holes, verifying the input shaft faces the tractor PTO and the output shaft aligns with the blade hub or rotor.
  6. Ensure the PTO shaft has at least 50% spline overlap in all operating positions. Inadequate overlap causes rapid spline wear and potential shaft separation.
  7. Record the installation date, tractor hour meter reading, and gearbox serial number in your maintenance log for warranty and service interval tracking.

โ“ Soalan Lazim

❓ What is the difference between ratio options?

Ratio determines the speed/torque trade-off at the output. 1:1 maintains PTO speed (high blade RPM); 1:1.93 nearly halves output speed while doubling torque. Choose based on your target blade tip speed and vegetation density.

❓ What is the lead time for standard models?

In-stock standard models ship within 3-5 business days. For models requiring custom ratios or configurations, typical lead time is 4-6 weeks. Rush production is available for urgent requirements.

❓ How do I select the right gear ratio?

Match the ratio to your blade tip speed target. Lower ratios (e.g. 1:1) give higher blade RPM for finish mowing; higher ratios (e.g. 1:1.93 or above) trade speed for torque, ideal for thick brush. Calculate: output RPM = input RPM รท ratio.

❓ What is the expected operational lifespan?

With proper maintenance, our gearboxes typically deliver 3,000 to 5,000 operating hours. Many units in the field have exceeded 6,000 hours. Lifespan depends on operating load, maintenance compliance, and field conditions.

❓ Is this suitable for mulching applications?

Yes. Our gearboxes are widely used on mulching mowers and brush cutters. For mulching, select a model rated 25-30% above your actual PTO horsepower to provide a safety margin against the intermittent shock loads typical of mulching.

โญ Ulasan Pelanggan & Laporan Lapangan

★★★★★

📍 Western Australia, Australia

We ordered in bulk for our dealer network. Customer return rate is near zero. That speaks volumes about reliability.

★★★★★

📍 Bordeaux, France

Fast shipping, professional packaging, and the gearbox itself is built like a tank. Highly recommended for serious agricultural work.

★★★★★

📍 Adana, Turkey

Installed on a disc mower that sees 8+ hours of use per day during season. Absolutely dependable. That is all I ask of a gearbox.

★★★★☆

📍 Saskatchewan, Canada

Kami menyelenggara lebih 40 mesin pemotong rumput untuk kontrak majlis. Beralih kepada jenama ini telah mengurangkan kadar kegagalan kotak gear kami sebanyak lebih 60 peratus.

★★★★☆

📍 Hokkaido, Japan

Berjalan dalam musim sejuk yang melampau (-25 ยฐC) dan musim panas yang panas. Minyak sintetik dalam kotak gear ini mengendalikan kedua-dua keadaan ekstrem tanpa masalah.

Julat kotak gear pertanian

⚖ EP-RC61T vs. Low-Cost Alternatives

Ciri EP-RC61T (Ever-power) Alternatif Generik / Kos Rendah
Bearing Preload ✔ Precision Shimmed, Zero End-Play ✘ No Preload Adjustment, Excessive Play
Gasket System ✔ Fluorocarbon O-Ring, No Re-Torque Needed ✘ Paper Gasket, Requires Annual Re-Torque
Lubrication System ✔ Splash + Directional Baffles, Full Coverage ✘ Basic Splash Only, Uneven Distribution
Housing ✔ Ductile Cast Iron or HT250 Grey Iron, 12-14mm Wall ✘ Thin-Wall Recycled Cast Iron, 8mm Wall
Surface Finish ✔ E-Coat Primer + Powder Coat, 80ฮผm Total ✘ Spray Paint, 30-40ฮผm, Chips Within Months
Noise Level ✔ 72-78 dB at 1m, Spiral Bevel Design ✘ 82-88 dB at 1m, Straight Bevel Design
Bearing Installation ✔ Interference Fit via Induction Heating ✘ Press Fit, Risk of Spinning-In-Bore

๐Ÿ”„ Produk & Aksesori Berkaitan

๐Ÿ† Pensijilan & Piawaian Kualiti

Our manufacturing facility holds ISO 9001:2015 quality management and ISO 14001:2015 environmental management certifications. All gear steel is supplied with EN 10204 Type 3.1 mill test certificates. Heat treatment processes are monitored per CQI-9 (Special Process: Heat Treat System Assessment). Every EP-RC61T undergoes 100% dimensional inspection and functional testing before shipment.

๐Ÿญ Mengapa Memilih Ever-power Australia Mower Gearbox Co.,Ltd.?

At Ever-power Australia Mower Gearbox Co.,Ltd., we have invested over two decades building one of the most advanced agricultural gearbox production facilities in the Asia-Pacific region. Our 22500 mยฒ campus integrates in-house forging, CNC gear cutting, automated heat treatment, precision grinding, and assembly under one roof โ€” giving us end-to-end quality control that outsourced manufacturers simply cannot match. We produce 66000 gearbox units annually, serving OEM partners and distributors across 41+ countries on six continents, with particular strength in the Australian, North American, and European markets.

Aci pemacu PTO

📞 Get Your EP-RC61T Quote Today

Ready to boost your mowing productivity with the EP-RC61T? Our application engineers can match this gearbox to your specific tractor and implement โ€” get a tailored recommendation today.

Minta Sebut HargaLayari Semua Produk

Produk berkaitan