EP-01-707 Lawn Mower Gearbox

EP-01-707 Lawn Mower Gearbox

The EP-01-707 pairs a 1:1.44 ratio with module 6 gears and 1 3/4 Z20 spline input to deliver 60 HP reliably. Municipal councils and highway departments select this model for its balance of output speed, torque, and service weight — heavy enough for durability, light enough for standard three-point hitch mounting.

SKU: 42432a702cff Category: Tags: , , , ,

وصف


EP-01-707 — Professional-Grade Medium-Duty Rotary Cutter Gearbox for Agricultural Mowing

ال EP-01-707 is a purpose-engineered lawn mower gearbox delivering reliable right-angle power transmission at 60 حصان with 540 دورة في الدقيقة PTO input. Its spiral bevel gears and sealed construction ensure consistent performance across thousands of operating hours in demanding field conditions.

EP-01-707 Medium-Duty Rotary Cutter Gearbox

📈 EP-01-707 Technical Specifications

المعلمة مواصفة
رقم الموديل EP-01-707
نوع علبة التروس Medium-Duty Rotary Cutter Gearbox
نسبة التروس 1:1.44
تكوين الأسنان 23/16
وحدة التروس 6
القدرة المقدرة 60 حصان
سرعة الإدخال 540 دورة في الدقيقة
عمود الإدخال/الإخراج 1 3/4 Z20 / Taper spline
الوزن الصافي 37 Kg
مادة التروس فولاذ سبيكي 20CrMnTi، مُكربن ومُقسّى HRC 58-62
مواد البناء حديد الزهر الرمادي (HT200/HT250)
حماية الختم موانع تسرب زيت متعددة الحواف من مادة NBR/FKM، حاصلة على تصنيف IP65+
تشحيم زيت تروس SAE 80W-90 أو 85W-140 EP
معالجة السطح طبقة أساسية مطلية بالكهرباء + طبقة مسحوق بوليستر، لون أحمر

⭐ الميزات الرئيسية والمزايا الهندسية

🔒

Pressurized Internal Oil Pump

Gear-driven micro-pump maintains positive lubrication pressure at all critical contacts, enabling safe operation on slopes exceeding 40° without oil starvation.

⚡

Lightweight AlSi7Mg T6 Housing

Aluminum-silicon alloy housing with T6 temper provides excellent thermal conductivity for cooler operation and natural corrosion resistance in wet haymaking environments.

🔄

Sealed-for-Life Bearing Pack

Bearings factory-packed with Mobil XHP 222 high-temp grease, delivering 1,500 hours of maintenance-free disc mower operation before re-greasing is needed.

🔨

Space-Optimized Thin-Wall Enclosure

Compact aluminum or thin-wall iron casing for applications where overall gearbox envelope and weight are hard-limited by implement frame constraints.

🌡

Multi-Position Bolt Pattern

Versatile mounting interface with tapped holes at 0°, 90°, and 180° orientations, fitting a wide range of implement frame geometries without adapter plates.

🛠

E-Coat + Powder Coat Finish

25 μm zinc-rich e-coat primer plus 80 μm polyester powder topcoat provides 1,000+ hours of ASTM B117 salt-spray corrosion resistance.

Mower gearbox in agricultural use

🔧 توافق المعدات والمراجع المتبادلة

🔄 Cross-Reference Compatibility for EP-01-707

The EP-01-707 is engineered as a direct replacement or upgrade for gearboxes fitted to equipment from leading manufacturers including:

Massey Ferguson • Deutz-Fahr • Woods • Krone • McConnel • Fendt • Iseki • YTO

إخلاء مسؤولية: تُستخدم أسماء العلامات التجارية المذكورة أعلاه لأغراض تحديد التوافق فقط. شركة إيفر-باور أستراليا لتصنيع علب تروس جزازات العشب المحدودة ليست تابعة لأي من الشركات المصنعة المذكورة، ولا معتمدة منها، ولا مرخصة لها. جميع العلامات التجارية مملوكة لأصحابها المعنيين.

📚 دليل اختيار علبة التروس

Choosing the right mower gearbox is critical for implement performance and longevity. Use the following criteria when evaluating the EP-01-707:

📌 مطابقة نسبة التروس مع سرعة طرف الشفرة
For the EP-01-707 with ratio(s) 1:1.44, calculate your required blade tip speed: typically 4,500-5,500 m/min for standard rotary cutters, 3,000-4,000 m/min for heavy brush cutting, and 5,500-6,500 m/min for fine finish mowing. Output RPM = PTO RPM ÷ ratio. Multiply by blade diameter to get tip speed.
📌 تحديد حجم قدرة المحرك بالحصان (PTO) للجرار
The EP-01-707 is rated at 60 HP. Always select a gearbox rated at or above your tractor’s maximum PTO horsepower. For shock-load applications (mulching, brush clearing), add a 25-30% safety margin: a 60 HP tractor should use a 75+ HP rated gearbox.
📌 اختيار سرعة دوران عمود إدارة الطاقة (PTO) بين 540 دورة في الدقيقة و1000 دورة في الدقيقة
The EP-01-707 operates at 540 rpm. Most rotary mowers use 540 RPM PTO. The 1000 RPM standard is for larger implements on high-HP tractors. Never connect a 540 RPM gearbox to a 1000 RPM PTO — the doubled speed will destroy bearings and gears within minutes.
📌 Cast Iron Housing vs Aluminium Housing
The EP-01-707 uses a grey cast iron housing. Cast iron excels in vibration damping, impact resistance, and heat dissipation — ideal for rough, rocky mowing conditions. Aluminium is lighter and more corrosion-resistant, better suited to wet environments and weight-sensitive implements.
📌 Standard Catalog vs Custom Specification
The EP-01-707 is available as a standard catalog item shipping in 3-5 days. If your application requires a non-standard ratio, shaft type, or mounting configuration, our engineering team offers custom designs with 4-6 week lead times. Minimum order quantities may apply.

🌾 سيناريوهات التطبيق النموذجية

🌾 Firebreak establishment and maintenance mowing

🚘 Disc mowing of grass and legume hay crops

🌱 Airfield perimeter and runway strip grass management

⛰ Sugar cane and crop stubble field mulching

🌳 Dairy farm laneway and yard surround maintenance

Ever-power Australia Mower Gearbox Co.,Ltd. manufacturing facility

🛠 دليل التثبيت والإعداد

  1. After the first 10 hours of operation, re-torque all mounting bolts to specification and verify oil level. Perform the first oil drain and refill at 50 hours.
  2. Disconnect the tractor PTO shaft and safely support the mower implement on jack stands or blocks before beginning the gearbox installation procedure.
  3. For units weighing over 25 kg, use a chain hoist, engine crane, or two-person lift to position the gearbox. Never attempt to lift heavy gearboxes solo.
  4. Fill the gearbox with the recommended gear oil (SAE 80W-90 or 85W-140 EP) to the level indicated on the sight glass or dipstick. Do not overfill.
  5. قبل التشغيل بكامل الحمل، قم بتشغيله من خلال تسلسل تليين تدريجي: 30 دقيقة بنصف الخانق، ثم 30 دقيقة بثلاثة أرباع الخانق، قبل تشغيل سرعة PTO الكاملة.
  6. افحص قاعدة تثبيت الآلة للتأكد من استوائها باستخدام مسطرة مستقيمة. يجب تصحيح أي اعوجاج يتجاوز 0.5 مم قبل تركيب علبة التروس الجديدة.
  7. استخدم غسالات Nord-Lock أو مركب تثبيت الخيوط على جميع مسامير التثبيت لمنع الارتخاء الناتج عن الاهتزاز أثناء التشغيل.

❓ الأسئلة الشائعة

❓ How noisy is this gearbox during operation?

Our spiral bevel designs produce 72-78 dB(A) at 1 metre under rated load — significantly quieter than straight-bevel alternatives (typically 82-88 dB). Operators notice a meaningful reduction in gear whine.

❓ What is the difference between ratio options?

Ratio determines the speed/torque trade-off at the output. 1:1 maintains PTO speed (high blade RPM); 1:1.93 nearly halves output speed while doubling torque. Choose based on your target blade tip speed and vegetation density.

❓ What is the lead time for standard models?

In-stock standard models ship within 3-5 business days. For models requiring custom ratios or configurations, typical lead time is 4-6 weeks. Rush production is available for urgent requirements.

❓ How do I select the right gear ratio?

Match the ratio to your blade tip speed target. Lower ratios (e.g. 1:1) give higher blade RPM for finish mowing; higher ratios (e.g. 1:1.93 or above) trade speed for torque, ideal for thick brush. Calculate: output RPM = input RPM ÷ ratio.

❓ What is the expected operational lifespan?

With proper maintenance, our gearboxes typically deliver 3,000 to 5,000 operating hours. Many units in the field have exceeded 6,000 hours. Lifespan depends on operating load, maintenance compliance, and field conditions.

⭐ آراء العملاء وتقارير ميدانية

★★★★★

📍 Victoria, Australia

Good quality for the price. Our crew runs these gearboxes hard and they hold up better than previous brands we have tried.

★★★★★

📍 ولاية أيوا، الولايات المتحدة الأمريكية

We fitted six of these across our fleet. Every single unit has performed flawlessly through two complete cutting seasons.

★★★★★

📍 فيصل آباد، باكستان

Excellent for orchard floor management. The cooling fin design makes maintenance easy and keeps unplanned downtime to a minimum.

★★★★☆

📍 بولتافا، أوكرانيا

Runs noticeably cooler than the old gearbox it replaced. The improved cooling design and better oil volume are making a real difference.

★★★★☆

📍 Córdoba, Argentina

We tested this against a competitor unit side by side. This one runs quieter, stays cooler, and the oil stayed cleaner over 200 hours.

Agricultural gearbox range

⚖ EP-01-707 vs. Low-Cost Alternatives

ميزة EP-01-707 (Ever-power) بديل عام / منخفض التكلفة
سدادة التصريف ✔ سدادة مغناطيسية تلتقط جزيئات التآكل ✘ قابس قياسي، لا يلتقط الجسيمات
إمكانية التتبع ✔ رقم تسلسلي محفور بالليزر، سجلات مواد كاملة ✘ لا يوجد رقم تسلسلي، لا يمكن تتبعه
تشكيل الهياكل ✔ ماكينة CNC خماسية المحاور، دقة تجويف IT6 ✘ نظام تحكم رقمي ثلاثي المحاور أو يدوي، دقة تجويف IT9
توافر قطع الغيار ✔ Full Inventory, Ships Within 24 Hours ✘ Limited Stock, 4-8 Week Back-Order
مهلة ✔ 3-5 أيام للخدمة القياسية، 4-6 أسابيع للخدمة المخصصة ✘ 8-12 أسبوعًا، لا يوجد خيار للتسريع
دقة التروس ✔ فئة AGMA 8-10، معالجة حرارية لاحقة باستخدام الحاسوب ✘ فئة AGMA 5-6، للتشكيل فقط، بدون طحن
سعة الزيت ✔ حوض تجميع واسع لتبريد ممتد، ونافذة رؤية ✘ كمية زيت قليلة، لا يوجد مؤشر مستوى

🔄 Related Products & Accessories

🏆 Certifications & Quality Standards

Our manufacturing facility holds ISO 9001:2015 quality management and ISO 14001:2015 environmental management certifications. All gear steel is supplied with EN 10204 Type 3.1 mill test certificates. Heat treatment processes are monitored per CQI-9 (Special Process: Heat Treat System Assessment). Every EP-01-707 undergoes 100% dimensional inspection and functional testing before shipment.

🏭 Why Choose Ever-power Australia Mower Gearbox Co.,Ltd.?

At Ever-power Australia Mower Gearbox Co.,Ltd., we have invested over two decades building one of the most advanced agricultural gearbox production facilities in the Asia-Pacific region. Our 19000 m² campus integrates in-house forging, CNC gear cutting, automated heat treatment, precision grinding, and assembly under one roof — giving us end-to-end quality control that outsourced manufacturers simply cannot match. We produce 59000 gearbox units annually, serving OEM partners and distributors across 49+ countries on six continents, with particular strength in the Australian, North American, and European markets.

PTO drive shaft

📞 Get Your EP-01-707 Quote Today

Ready to boost your mowing productivity with the EP-01-707? Our application engineers can match this gearbox to your specific tractor and implement — get a tailored recommendation today.

Request a QuoteBrowse All Products

Related products