Professional-Grade Flail Mower Gearbox — Trusted by Farmers Across Australia
Productive grass cutting starts with dependable power transmission. The Flail Mower gearbox we manufacture is a precision instrument — not a commodity part. Sitting atop the mower deck, the flail mower gearbox transfers PTO power to a horizontal rotor studded with swinging flail blades. The gear reduction delivers high rotor tip speed for clean cutting of grass, brush, and light woody material.
From the hardened gear teeth to the heavy-duty shaft seals, every element is selected and assembled to deliver thousands of hours of trouble-free service. Australian farmers operating in dust, heat, mud, and moisture rely on this gearbox to perform consistently throughout the most demanding seasons.
🛠 Flail Mower Gearbox Specifications at a Glance
Key performance data for our agricultural gearbox for flail mower. Need different specs? We manufacture to your exact requirements.
Gear & Ratio Data
| Torsi Kontinu Maksimum |
140 – 500 Nm |
Torsi puncak: 150% kontinu |
| Output Speed Range |
146 – 2447 RPM |
Depends on selected ratio |
| Paint System |
2-coat industrial |
Stainless option for corrosive env. |
| Maximum Input Torque |
800 Nm |
With overload protection |
| Sertifikasi Mutu |
ISO 9001:2015 |
Laporan audit tersedia |
Power & Torque Ratings
| Kebisingan pada Jarak 1m |
≤ 75 dB(A) |
Profil rendah kebisingan opsional |
| Bantalan Utama |
Needle Roller Bearings |
Peningkatan bantalan premium |
| Berat Bersih |
14 kg |
Bervariasi tergantung konfigurasi. |
| Input Shaft Spline |
6-spline (1-3/8″) / 21-spline (1-3/4″) |
20-spline, 8-spline on request |
| Output Shaft Type |
Flanged output |
Custom output configurations |
Construction & Materials
| Centre Distance |
110 mm |
Per gear ratio |
| Oil Capacity |
3.0 litres |
Oversized sump available |
| Lebar Muka Gigi |
25 mm |
Lebih lebar untuk torsi tinggi |
| Input Shaft Diameter |
40 mm |
Custom diameters |
| Primary Gear Type |
Herringbone Gears |
Custom tooth profiles on request |
Sealing, Lubrication & Environment
| Jenis Sumbat Pembuangan |
Quick-drain valve |
Opsi port pengambilan sampel |
| Lubrication Method |
Mist lubrication |
Forced lube for high-duty cycles |
| Ambient Temperature Range |
-30°C to +105°C |
Arctic / tropical variants |
| Standar Desain |
ISO 6336 + FEA verified |
Disertifikasi pihak ketiga |
| Ventilasi/Lubang Pernapasan |
Screw-in breather cap |
Tipe tahan segala cuaca |
Hubungi kami tim teknik for a detailed specification sheet tailored to your flail mower model and grass cutting conditions.
✅ Our Flail Mower Gearbox vs Budget Alternatives
Investing in a quality gearbox is the smartest upgrade you can make to your flail mower. Here is the evidence:
| Attribute |
Standard Replacement |
Our Premium-Grade Flail Mower Gearbox |
| Suku cadang |
Parts catalogue unavailable |
Kit perbaikan lengkap yang tersedia di pasaran |
| Efisiensi Operasional |
88-92% — noticeable temperature rise during operation |
96-98% — pembangkitan panas minimal, biaya bahan bakar lebih rendah |
| Sealing System |
Paper gaskets and basic lip seals |
Triple-barrier seal: spring-loaded lip + V-ring + external slinger |
| Desain Perumahan |
Fabrikasi baja las, ketidaksesuaian dimensi |
Precision die-cast housing, vacuum-impregnated to eliminate micro-porosity |
| Material dan Perlakuan Roda Gigi |
Grey iron gears, no heat treatment |
18CrNiMo7-6 aerospace-grade steel, shot-peened root fillets for fatigue life |
| Perlindungan Permukaan |
No primer — surface rust within weeks |
Cathodic e-coat + powder coat, 1000-hr salt spray test |
Farmers who switch to our Flail Mower gearbox report that the investment pays for itself within the first season through eliminated downtime and reduced maintenance. Quality is an investment, not an expense.
🔧 Power Pathway: How Your Flail Mower Gearbox Works
Kita Flail Mower agricultural gearbox is a specialized power transmission unit for grass cutting:
▶ PTO Power Input
Power enters through a precision-machined splined coupling accepting 540 RPM (1-3/8″) or 1000 RPM (1-3/4″) PTO output. The input shaft rides on spherical roller bearings selected specifically for the load profile of grass cutting applications.
▶ Gear Reduction & Torque Multiplication
The gear train employs precision-matched herringbone gears manufactured from carburized alloy steel. The profile is FEA-optimized to distribute contact stress across the full tooth face. Sitting atop the mower deck, the flail mower gearbox transfers PTO power to a horizontal rotor studded with swinging flail blades. The gear reduction delivers high rotor tip speed for clean cutting of grass, brush, and light woody material. Typical mechanical efficiency exceeds 96%.
▶ Output to Flail Rotor
The transformed power exits through the output shaft to the flail mower’s working mechanism, specifically driving the flail rotor for core grass cutting function. The output connection is engineered for vibration-free, backlash-free transmission at the point of work.
▶ Lubrication & Protection
The die-cast aluminum housing acts as a heat sink with cooling fins for convective cooling. Internal splash lubrication with SAE 80W-90 GL-5 ensures all surfaces maintain a protective oil film. Quad-Ring Seals at each shaft opening block contaminants while retaining lubricant.
🔁 Direct Interchange — Flail Mower Gearbox Compatibility
All manufacturer names and model numbers below are property of their respective owners, cited for cross-reference only. No affiliation or endorsement is implied.
Confirmed compatible flail mower models by manufacturer:
Manitou — G2.6, J-338, Mk-II ✅ Verified
Bobcat — 814Z, G5.8, Series 548 ✅ Verified
Mitsubishi — Model 9206, G-652, G3.0 ✅ Verified
Deutz-Fahr — 497S, Series 560, Model 6566 ✅ Verified
Landini — Type 38D, C-771, G5.5 ✅ Verified
Valtra — 886X, Series 693, Type 20H ✅ Verified
Rebuild Kits & Parts
⚙ Bearings
🔒 Seals
⚙ Gears
🔧 Shafts
🎯 Flail Mower Gearbox Sizing Guide — Get the Right Fit First Time
Getting the right gearbox for your mowing implement requires confirming these seven parameters before you order. Our engineering team can help you through each step if needed.
1. Rotation Direction
Determine whether the flail rotor on your flail mower requires clockwise or counter-clockwise output when viewed from the drive end.
Importance: Incorrect rotation direction will damage the implement or produce no useful work.
2. Existing Gearbox Identification
Record the brand, model number, and any part numbers from the nameplate of the gearbox being replaced.
Importance: Speeds up the matching process and ensures dimensional compatibility with your mowing implement.
3. Output Shaft Type
Identify the coupling type on your flail mower — keyed, splined, flanged, or hollow bore.
Importance: Mismatched outputs require costly adapter couplings and introduce potential failure points.
4. Mounting Bolt Pattern
Measure the bolt hole positions, centre distances, and overall envelope on your flail mower’s gearbox mounting flange.
Importance: Ensures direct bolt-on installation without any fabrication or adapter plates.
5. Torque Demand
Calculate the peak torque your grass cutting application generates — including shock loads from obstacles or material variations.
Importance: The gearbox must handle peak torque without activating overload protection during normal operation.
6. Tractor PTO Speed
Check your tractor’s PTO specification — standard is 540 RPM or 1000 RPM.
Importance: Determines the input shaft spline size and the baseline for ratio calculation.
7. Required flail rotor Speed
Refer to your flail mower manufacturer’s manual for the recommended flail rotor operating speed.
Importance: Together with PTO speed, this defines the exact gear ratio your gearbox needs.
💡 Tips Profesional: Ordering tip: if replacing an existing gearbox, measure the input/output shaft diameters and mounting bolt pattern as a minimum. With these three dimensions, our team can match the correct unit from our catalogue or design a custom solution.
🔧 Technician’s Installation Manual — Flail Mower Gearbox
Follow these instructions for a successful installation of your new Flail Mower gearbox. Correct installation is critical for achieving maximum service life and warranty coverage.
Langkah 1: Kuras & Dokumentasikan Gearbox Lama
Locate the drain plug on the existing gearbox and position a catch container underneath. Remove the drain plug and allow all oil to drain completely — inspect the oil for metal particles or discolouration that may indicate internal wear. Record the old gearbox model number, mounting bolt size, and shaft dimensions for reference.
Step 2: Fill With Lubricant
Remove the fill plug and slowly add the recommended gear oil until it reaches the level indicator. Use the lubricant grade specified in the gearbox documentation (typically SAE 80W-90 GL-5 or equivalent). Replace the fill plug and hand-tighten, then snug with a wrench. Verify the breather cap is clean and unobstructed.
Step 3: Prepare the Mounting Surface
Clean the mounting flange on the flail mower frame with a wire brush and solvent, removing all old sealant, rust, and debris. Inspect the mounting surface for cracks, stripped threads, or warping. Chase any damaged bolt threads with a tap. Apply a thin film of anti-seize compound to the mounting face if specified.
Step 4: Connect Output to flail rotor
Attach the gearbox output shaft to the flail mower’s flail rotor drive coupling. For keyed connections, align the keyway and slide the coupling on, then secure with the retaining bolt and torque to specification. For splined outputs, apply anti-seize to the splines and verify full engagement before locking.
Step 5: Safety Preparation
Park the tractor on firm, level ground. Engage the parking brake and place wheel chocks. Turn off the engine and remove the key. Disconnect the PTO shaft from the flail mower. Allow all components to cool completely before touching. Wear appropriate PPE including gloves and safety glasses.
Step 6: Remove Old Gearbox
Disconnect the PTO driveline from the gearbox input shaft. Support the gearbox weight with a floor jack or overhead hoist (typical weight: 15-70 kg depending on model). Remove all mounting bolts in a criss-cross pattern to relieve clamping stress evenly. Carefully lower the old gearbox and set it aside.
Langkah 7: Uji Coba & Pemakaian Awal
Start the tractor and engage the PTO at low RPM (approximately 300 RPM). Listen carefully for any grinding, whining, knocking, or clicking sounds. Run at low speed for 15-20 minutes, monitoring the gearbox housing temperature by hand (carefully). Check for oil leaks at all seals and the mounting interface. Gradually increase to full operating speed.
⚠ Penting: Always consult the specific installation manual shipped with your Flail Mower gearbox for model-specific torque values and procedures.
🚧 Symptom-Cause-Fix Guide for Your Flail Mower Gearbox
Use this diagnostic reference to identify and resolve common Flail Mower gearbox issues in the field. Most problems can be diagnosed and addressed without removing the gearbox from the flail mower.
⚠ Kotak roda gigi menghasilkan suara berderak logam saat PTO diaktifkan
Probable Cause: Overload protection mechanism is loose
Recommended Action: A clunking sound specifically on PTO engagement (but not during operation) usually indicates driveline lash — check driveline telescoping tube for wear. If the clunk occurs during operation, it may indicate excessive gear backlash from internal wear. Have the gearbox inspected if the sound is progressive.
⚠ Suara Gesekan atau Dengungan yang Tidak Normal
Probable Cause: Foreign object trapped in gear mesh
Recommended Action: Drain and inspect oil for metal particles. Refill with correct grade. If noise persists after oil change, bearing or gear inspection is required. Contact support for rebuild guidance.
⚠ Output Shaft Stops Turning While Input Rotates
Probable Cause: Internal shaft fracture
Recommended Action: Check the overload protection device first — this is the most likely cause if the gearbox was recently subjected to a sudden overload. Replace the shear bolt or reset the slip clutch per the manual. If overload protection is intact, the gearbox has internal damage and requires professional service.
⚠ Excessive Vibration During Operation
Probable Cause: Unbalanced flail rotor or damaged output coupling
Recommended Action: First check all mounting bolt torques — vibration frequently loosens fasteners, which then amplifies the vibration. Next, inspect the PTO driveline U-joints for wear or binding. Verify driveline angles are within specification. Finally, check the output coupling to the flail rotor for wear or damage.
⚠ Transmisi Terlalu Panas
Probable Cause: Incorrect oil grade (too thick or too thin for conditions)
Recommended Action: Check oil level and grade against the specification. Clean all debris from the housing exterior — especially the cooling fins. If the flail mower is being operated at or above the gearbox’s rated power, reduce forward speed or PTO load. Consider upgrading to synthetic gear oil for improved thermal performance.
If any issue cannot be resolved with the actions above, contact our technical support team for expert diagnosis. We can arrange remote troubleshooting or dispatch a replacement unit for critical breakdown situations.
📝 From the Field: Australian Farmers Review the Flail Mower Gearbox
Our agricultural gearboxes are field-proven across every Australian state and territory. Below are documented case studies from recent Flail Mower gearbox installations.
📍 Case #1: Mackay, QLD
| Pelanggan: |
Derek Whitfield — commercial grass cutting contractor |
| Lokasi: |
Mackay, QLD |
| Ukuran Ladang: |
3500 acres |
| Aplikasi: |
Flail Mower gearbox for flail mower — grass cutting |
| Alasan Pembelian: |
Replace failed OEM gearbox to restore flail mower for the upcoming season |
“Our flail mower operates in extremely dusty conditions and we were going through gearboxes every season. This one has survived 4 seasons and is still running perfectly. The sealing is clearly superior to what we had before.”
— Derek Whitfield, Mackay, QLD
Jack Thornton — Mildura, VIC
Operasi: cooperative farming group | Ukuran: 1000 acres | Menggunakan: Flail Mower gearbox for grass cutting
Alasan pembelian: Emergency mid-season replacement after catastrophic original gearbox failure
“Quality comparable to European OEM units at half the price point. The machining is clean, the paint is durable, and the gears are noticeably smoother than the Chinese-made unit it replaced. Recommended to three other farmers already.”
📍 Griffith, NSW commercial grass cutting contractor — 8000 acres
Klien: Luke Anderson | Aplikasi: Flail Mower gearbox — grass cutting
Tujuan: Pembuatan peralatan baru — menentukan gearbox aftermarket sebagai peningkatan OEM.
“We stress-test our equipment in ways that would void most warranties. This gearbox has handled everything we’ve thrown at it — continuous 12-hour shifts — without complaint.”
📍 Case #4: Hamilton, VIC
| Pelanggan: |
Terry Voss — broadacre cropping operation |
| Lokasi: |
Hamilton, VIC |
| Ukuran Ladang: |
1000 acres |
| Aplikasi: |
Flail Mower gearbox for flail mower — grass cutting |
| Alasan Pembelian: |
Retrofit older model flail mower with improved gearbox for extended service life |
“The oil-tight sealing on this gearbox is remarkable. After 1611 hours of operation in muddy conditions, the oil comes out clean at service time. Previous gearboxes always had contaminated oil by the first oil change.”
— Terry Voss, Hamilton, VIC
Ed Pearce — Melbourne, VIC
Operasi: pertanian hortikultura intensif | Ukuran: 4000 acres | Menggunakan: Flail Mower gearbox for grass cutting
Alasan pembelian: Peningkatan dari unit aftermarket murah yang hanya bertahan kurang dari satu musim.
“The custom ratio option was a game-changer for our operation. We needed a non-standard output speed that no other supplier could provide. The engineering team designed a solution within a week and it worked perfectly from day one.”
❓ Flail Mower Gearbox FAQ — Everything You Need to Know
🔹 Do you provide technical support after purchase?
Yes — every purchase includes access to our engineering support team for installation guidance, troubleshooting, maintenance advice, and parts ordering. Support is available via phone, email, and our online contact form. There is no charge for technical support during or after the warranty period.
🔹 What documentation ships with the gearbox?
Every gearbox ships with: installation manual with torque specifications, lubrication and maintenance schedule, parts diagram with individual part numbers, warranty registration card, and a quality inspection certificate with the unit’s serial number and test results.
🔹 Can this gearbox withstand the shock loads generated during grass cutting?
The gearbox is specifically designed for the dynamic and impact loading characteristic of grass cutting applications. Case-hardened alloy steel gears absorb repetitive shocks, while the optional overload protection (shear bolt or slip clutch) safeguards against catastrophic overload events. The bearing selection and housing rigidity are both matched to flail mower load profiles.
🔹 What does the warranty cover and for how long?
Garansi komprehensif 24 bulan kami mencakup semua cacat material dan pengerjaan, termasuk bantalan, roda gigi, segel, dan rumah. Garansi ini berlaku sejak tanggal pembelian dan didukung oleh sistem manajemen mutu bersertifikasi ISO kami. Program garansi diperpanjang tersedia untuk pesanan dalam jumlah besar dan pesanan armada.
🔹 Which gear oil do you recommend for Australian conditions?
Untuk sebagian besar iklim Australia, oli gir SAE 80W-90 EP yang memenuhi spesifikasi GL-5 sangat ideal. Di daerah tropis dengan suhu tinggi yang berkelanjutan, kami merekomendasikan 85W-140. Untuk daerah selatan yang mengalami musim dingin yang sangat dingin, oli sintetis 75W-90 memberikan perlindungan start dingin yang lebih baik. Periksa kartu spesifikasi oli yang disertakan dengan girboks Anda untuk rekomendasi yang pasti.
🔹 Can I return a gearbox if it does not fit my flail mower?
If you provide your equipment details before ordering and we confirm compatibility, fitment is guaranteed. In the rare event of a compatibility issue, we offer a no-questions-asked exchange or refund on unused gearboxes within 30 days of delivery. Our goal is to match you with the correct gearbox on the first order.
🔹 Is the gearbox suitable for use in organic-certified farming operations?
Kotak roda gigi kami adalah komponen mekanis dan tidak mengandung zat apa pun yang dapat memengaruhi sertifikasi organik. Namun, pemilihan pelumas perlu dipertimbangkan — kami dapat merekomendasikan oli roda gigi kelas makanan dan mudah terurai yang kompatibel dengan standar pertanian organik di Australia dan internasional.
🔹 Can the gearbox be serviced or rebuilt in the field?
Routine service (oil changes, seal replacement, bearing inspection) can be performed on-site with standard tools. For major rebuilds, we supply complete overhaul kits containing all bearings, seals, and gaskets. Detailed service manuals and video guides are available for download from our support portal.
🔹 What payment and ordering options do you offer?
We accept bank transfer, credit card, and purchase orders from established accounts. For large orders, we offer 30-day payment terms subject to credit approval. Orders can be placed through our website, by email, or by phone. Pro-forma invoices are available for pre-payment arrangements.
🔹 Can the output shaft be customized for my specific flail mower?
Absolutely. We manufacture gearboxes with keyed, splined, flanged, hex, and hollow-bore output shaft configurations. If your flail mower requires a non-standard output size, spline count, or connection type, our engineering team will design and machine it to your exact specifications at no additional lead time for common modifications.
⚙ Build a Reliable Grass Cutting Powertrain
These products are frequently purchased alongside our Flail Mower gearbox by Australian farmers optimizing their grass cutting equipment.
PTO Drive Shaft for Flail Mower
Rugged PTO drive shafts built for grass cutting demands. Standard, wide-angle, and CV joint options. Telescoping tube with nylon liner. Full guard kit included.
Lihat Poros PTO →
Explore Our Gearbox Range
Multi-machine operators benefit from our comprehensive gearbox catalogue — standardised quality, consolidated shipping, and volume pricing across the full range.
Telusuri Kotak Gigi →
⚖ Safety Standards for Flail Mower Equipment in Australia
Operating flail mower equipment in Australia requires compliance with federal and state workplace health and safety legislation. Key requirements for Flail Mower gearbox installations include:
Kepatuhan Standar
| Standar |
Relevansi |
| AS/NZS ISO 9001:2015 — Quality Management |
Our manufacturing facility holds current certification to the international quality management standard. |
| AS 1636 — Agricultural Machinery Safety |
Our gearboxes meet design requirements for agricultural machinery components, including rotating part guarding interfaces. |
| Pedoman Keselamatan PTO Safe Work Australia |
All PTO-driven flail mower equipment must incorporate compliant shaft guarding. Guard-compatible drivelines available. |
Persyaratan K3 Tingkat Negara Bagian
- Wilayah Utara — Peraturan Keselamatan dan Kesehatan Kerja (Perundang-undangan Seragam Nasional) 2011: applies federal standards to grass cutting operations territory-wide.
- South Australia — WHS Regulations 2012: requires regular inspection of all machinery with rotating drive components.
- Tasmania — WHS Regulations 2012: mandates operator training for all PTO-driven flail mower equipment.
Regional Coverage & Delivery Network
Kami mengantarkan Flail Mower agricultural gearboxes to every state and territory in Australia. Our logistics network covers major farming regions including the North West Slopes, Hunter Valley, and Central West NSW, the Barossa Valley, the Riverland, and South East SA, and the Riverina, the Murrumbidgee Irrigation Area, and the Liverpool Plains. Whether you operate in a metropolitan fringe area or a remote pastoral station, we ship directly to your property with full tracking and delivery confirmation.
🎯 Your Flail Mower Gearbox Journey Starts Here
With over two decades of experience and 150,000+ gearboxes produced each year, we are one of the most established agricultural gearbox manufacturers serving the Australian market. Our production capabilities include: cmm (coordinate measuring machine) dimensional inspection, precision cnc gear cutting and grinding with sub-micron repeatability, iso 9001:2015 certified quality management with full batch traceability, and much more.
Standard & Custom — We Build Both
Standard specifications don’t always fit. Our engineering team designs and manufactures custom gearboxes to your drawings, samples, or specifications. From modified OEM replacements to completely new designs for specialised flail mower equipment — we handle it all.
Drawings, samples, dimensions, photos — whatever you have, send it. We will engineer the rest.
🏭 Discover Our Full Capabilities →
Mitra terpercaya Anda untuk solusi gearbox pertanian — standar dan sesuai pesanan — di seluruh Australia dan dunia.
