Professional-Grade Flail Mower Gearbox — Trusted by Farmers Across Australia
Productive grass cutting starts with dependable power transmission. The Flail Mower gearbox we manufacture is a precision instrument — not a commodity part. Sitting atop the mower deck, the flail mower gearbox transfers PTO power to a horizontal rotor studded with swinging flail blades. The gear reduction delivers high rotor tip speed for clean cutting of grass, brush, and light woody material.
From the hardened gear teeth to the heavy-duty shaft seals, every element is selected and assembled to deliver thousands of hours of trouble-free service. Australian farmers operating in dust, heat, mud, and moisture rely on this gearbox to perform consistently throughout the most demanding seasons.
🛠 Flail Mower Gearbox Specifications at a Glance
Kluczowe dane dotyczące naszej wydajności agricultural gearbox for flail mowerPotrzebujesz innych specyfikacji? Produkujemy dokładnie według Twoich wymagań.
Dane dotyczące biegów i przełożeń
| Maksymalny ciągły moment obrotowy |
140 – 500 Nm |
Maksymalny moment obrotowy: 150% ciągłego |
| Output Speed Range |
146 – 2447 RPM |
Depends on selected ratio |
| System malarski |
2-coat industrial |
Wersja ze stali nierdzewnej do środowisk korozyjnych. |
| Maximum Input Torque |
800 Nm |
With overload protection |
| Quality Certification |
ISO 9001:2015 |
Audit reports available |
Moc i moment obrotowy
| Noise at 1m Distance |
≤ 75 dB(A) |
Low-noise profiles optional |
| Łożyska pierwotne |
Needle Roller Bearings |
Ulepszenia łożysk premium |
| Waga netto |
14 kg |
Zależy od konfiguracji |
| Wielowypust wału wejściowego |
6-rowkowy (1-3/8″) / 21-rowkowy (1-3/4″) |
20-rowkowe, 8-rowkowe na życzenie |
| Typ wału wyjściowego |
Wyjście kołnierzowe |
Niestandardowe konfiguracje wyjściowe |
Budownictwo i materiały
| Odległość między środkami |
110 mm |
Na przełożenie |
| Pojemność oleju |
3,0 litra |
Dostępny zbiornik o dużych rozmiarach |
| Gear Face Width |
25 mm |
Wider for high-torque |
| Input Shaft Diameter |
40 mm |
Custom diameters |
| Typ przekładni głównej |
Herringbone Gears |
Niestandardowe profile zębów na życzenie |
Uszczelnianie, smarowanie i środowisko
| Drain Plug Type |
Quick-drain valve |
Sampling port option |
| Lubrication Method |
Mist lubrication |
Forced lube for high-duty cycles |
| Zakres temperatur otoczenia |
-30°C to +105°C |
Warianty arktyczne / tropikalne |
| Standard projektowy |
ISO 6336 + FEA verified |
Certyfikowany przez stronę trzecią |
| Breather / Vent |
Screw-in breather cap |
All-weather types |
Skontaktuj się z nami zespół inżynierski for a detailed specification sheet tailored to your flail mower model and grass cutting conditions.
✅ Our Flail Mower Gearbox vs Budget Alternatives
Investing in a quality gearbox is the smartest upgrade you can make to your flail mower. Here is the evidence:
| Atrybut |
Standardowa wymiana |
Our Premium-Grade Flail Mower Gearbox |
| Części zapasowe |
Parts catalogue unavailable |
Complete rebuild kits off-the-shelf |
| Wydajność operacyjna |
88-92% — noticeable temperature rise during operation |
96-98% — minimal heat generation, lower fuel costs |
| System uszczelniający |
Paper gaskets and basic lip seals |
Uszczelnienie potrójnej bariery: warga sprężynowa + pierścień V + zewnętrzny pierścień odrzutowy |
| Projektowanie mieszkań |
Welded steel fabrication, dimensional inconsistency |
Precision die-cast housing, vacuum-impregnated to eliminate micro-porosity |
| Materiał i obróbka kół zębatych |
Grey iron gears, no heat treatment |
18CrNiMo7-6 aerospace-grade steel, shot-peened root fillets for fatigue life |
| Surface Protection |
No primer — surface rust within weeks |
Cathodic e-coat + powder coat, 1000-hr salt spray test |
Farmers who switch to our Flail Mower gearbox report that the investment pays for itself within the first season through eliminated downtime and reduced maintenance. Quality is an investment, not an expense.
🔧 Power Pathway: How Your Flail Mower Gearbox Works
Our Flail Mower agricultural gearbox is a specialized power transmission unit for grass cutting:
▶ PTO Power Input
Power enters through a precision-machined splined coupling accepting 540 RPM (1-3/8″) or 1000 RPM (1-3/4″) PTO output. The input shaft rides on spherical roller bearings selected specifically for the load profile of grass cutting applications.
▶ Gear Reduction & Torque Multiplication
The gear train employs precision-matched herringbone gears manufactured from carburized alloy steel. The profile is FEA-optimized to distribute contact stress across the full tooth face. Sitting atop the mower deck, the flail mower gearbox transfers PTO power to a horizontal rotor studded with swinging flail blades. The gear reduction delivers high rotor tip speed for clean cutting of grass, brush, and light woody material. Typical mechanical efficiency exceeds 96%.
▶ Output to Flail Rotor
The transformed power exits through the output shaft to the flail mower’s working mechanism, specifically driving the flail rotor for core grass cutting function. The output connection is engineered for vibration-free, backlash-free transmission at the point of work.
▶ Lubrication & Protection
The die-cast aluminum housing acts as a heat sink with cooling fins for convective cooling. Internal splash lubrication with SAE 80W-90 GL-5 ensures all surfaces maintain a protective oil film. Quad-Ring Seals at each shaft opening block contaminants while retaining lubricant.
🔁 Direct Interchange — Flail Mower Gearbox Compatibility
All manufacturer names and model numbers below are property of their respective owners, cited for cross-reference only. No affiliation or endorsement is implied.
Confirmed compatible flail mower models by manufacturer:
Manitou — G2.6, J-338, Mk-II ✅ Verified
Bobcat — 814Z, G5.8, Series 548 ✅ Verified
Mitsubishi — Model 9206, G-652, G3.0 ✅ Verified
Deutz-Fahr — 497S, Series 560, Model 6566 ✅ Verified
Landini — Type 38D, C-771, G5.5 ✅ Verified
Valtra — 886X, Series 693, Type 20H ✅ Verified
Rebuild Kits & Parts
⚙ Bearings
🔒 Seals
⚙ Gears
🔧 Shafts
🎯 Flail Mower Gearbox Sizing Guide — Get the Right Fit First Time
Getting the right gearbox for your mowing implement requires confirming these seven parameters before you order. Our engineering team can help you through each step if needed.
1. Rotation Direction
Determine whether the flail rotor on your flail mower requires clockwise or counter-clockwise output when viewed from the drive end.
Ważne: Nieprawidłowy kierunek obrotów może uszkodzić narzędzie lub uniemożliwić wykonanie jakiejkolwiek pracy.
2. Existing Gearbox Identification
Record the brand, model number, and any part numbers from the nameplate of the gearbox being replaced.
Importance: Speeds up the matching process and ensures dimensional compatibility with your mowing implement.
3. Typ wału wyjściowego
Identify the coupling type on your flail mower — keyed, splined, flanged, or hollow bore.
Znaczenie: Niedopasowane wyjścia wymagają kosztownych adapterów i stwarzają potencjalne punkty awarii.
4. Mounting Bolt Pattern
Measure the bolt hole positions, centre distances, and overall envelope on your flail mower’s gearbox mounting flange.
Znaczenie: Zapewnia bezpośredni montaż za pomocą śrub, bez konieczności stosowania żadnych dodatkowych elementów lub płyt adapterowych.
5. Torque Demand
Calculate the peak torque your grass cutting application generates — including shock loads from obstacles or material variations.
Importance: The gearbox must handle peak torque without activating overload protection during normal operation.
6. Prędkość WOM ciągnika
Sprawdź specyfikację WOM swojego ciągnika — standardowo wynosi 540 obr./min lub 1000 obr./min.
Znaczenie: Określa rozmiar wielowypustu wału wejściowego i punkt wyjścia do obliczenia przełożenia.
7. Required flail rotor Speed
Refer to your flail mower manufacturer’s manual for the recommended flail rotor operating speed.
Importance: Together with PTO speed, this defines the exact gear ratio your gearbox needs.
💡 Wskazówka: Wskazówka dotycząca zamawiania: w przypadku wymiany istniejącej skrzyni biegów, należy zmierzyć co najmniej średnice wału wejściowego/wyjściowego oraz rozstaw śrub montażowych. Dzięki tym trzem wymiarom nasz zespół może dobrać odpowiednią jednostkę z naszego katalogu lub zaprojektować rozwiązanie niestandardowe.
🔧 Technician’s Installation Manual — Flail Mower Gearbox
Follow these instructions for a successful installation of your new Flail Mower gearbox. Correct installation is critical for achieving maximum service life and warranty coverage.
Step 1: Drain & Document Old Gearbox
Locate the drain plug on the existing gearbox and position a catch container underneath. Remove the drain plug and allow all oil to drain completely — inspect the oil for metal particles or discolouration that may indicate internal wear. Record the old gearbox model number, mounting bolt size, and shaft dimensions for reference.
Step 2: Fill With Lubricant
Remove the fill plug and slowly add the recommended gear oil until it reaches the level indicator. Use the lubricant grade specified in the gearbox documentation (typically SAE 80W-90 GL-5 or equivalent). Replace the fill plug and hand-tighten, then snug with a wrench. Verify the breather cap is clean and unobstructed.
Step 3: Prepare the Mounting Surface
Clean the mounting flange on the flail mower frame with a wire brush and solvent, removing all old sealant, rust, and debris. Inspect the mounting surface for cracks, stripped threads, or warping. Chase any damaged bolt threads with a tap. Apply a thin film of anti-seize compound to the mounting face if specified.
Step 4: Connect Output to flail rotor
Attach the gearbox output shaft to the flail mower’s flail rotor drive coupling. For keyed connections, align the keyway and slide the coupling on, then secure with the retaining bolt and torque to specification. For splined outputs, apply anti-seize to the splines and verify full engagement before locking.
Step 5: Safety Preparation
Park the tractor on firm, level ground. Engage the parking brake and place wheel chocks. Turn off the engine and remove the key. Disconnect the PTO shaft from the flail mower. Allow all components to cool completely before touching. Wear appropriate PPE including gloves and safety glasses.
Step 6: Remove Old Gearbox
Disconnect the PTO driveline from the gearbox input shaft. Support the gearbox weight with a floor jack or overhead hoist (typical weight: 15-70 kg depending on model). Remove all mounting bolts in a criss-cross pattern to relieve clamping stress evenly. Carefully lower the old gearbox and set it aside.
Step 7: Test Run & Break-In
Start the tractor and engage the PTO at low RPM (approximately 300 RPM). Listen carefully for any grinding, whining, knocking, or clicking sounds. Run at low speed for 15-20 minutes, monitoring the gearbox housing temperature by hand (carefully). Check for oil leaks at all seals and the mounting interface. Gradually increase to full operating speed.
⚠ Ważne: Always consult the specific installation manual shipped with your Flail Mower gearbox for model-specific torque values and procedures.
🚧 Symptom-Cause-Fix Guide for Your Flail Mower Gearbox
Use this diagnostic reference to identify and resolve common Flail Mower gearbox issues in the field. Most problems can be diagnosed and addressed without removing the gearbox from the flail mower.
⚠ Skrzynia biegów wydaje metaliczny dźwięk stukania podczas włączania WOM
Probable Cause: Luźny mechanizm zabezpieczający przed przeciążeniem
Recommended Action: A clunking sound specifically on PTO engagement (but not during operation) usually indicates driveline lash — check driveline telescoping tube for wear. If the clunk occurs during operation, it may indicate excessive gear backlash from internal wear. Have the gearbox inspected if the sound is progressive.
⚠ Abnormal Grinding or Whining Noise
Probable Cause: Foreign object trapped in gear mesh
Recommended Action: Drain and inspect oil for metal particles. Refill with correct grade. If noise persists after oil change, bearing or gear inspection is required. Contact support for rebuild guidance.
⚠ Wał wyjściowy przestaje się obracać, podczas gdy wał wejściowy się obraca
Probable Cause: Wewnętrzne złamanie trzonu
Recommended Action: Check the overload protection device first — this is the most likely cause if the gearbox was recently subjected to a sudden overload. Replace the shear bolt or reset the slip clutch per the manual. If overload protection is intact, the gearbox has internal damage and requires professional service.
⚠ Excessive Vibration During Operation
Probable Cause: Unbalanced flail rotor or damaged output coupling
Recommended Action: First check all mounting bolt torques — vibration frequently loosens fasteners, which then amplifies the vibration. Next, inspect the PTO driveline U-joints for wear or binding. Verify driveline angles are within specification. Finally, check the output coupling to the flail rotor for wear or damage.
⚠ Skrzynia biegów pracuje nadmiernie
Probable Cause: Niewłaściwy gatunek oleju (zbyt gęsty lub zbyt rzadki do danych warunków)
Recommended Action: Check oil level and grade against the specification. Clean all debris from the housing exterior — especially the cooling fins. If the flail mower is being operated at or above the gearbox’s rated power, reduce forward speed or PTO load. Consider upgrading to synthetic gear oil for improved thermal performance.
If any issue cannot be resolved with the actions above, contact our technical support team for expert diagnosis. We can arrange remote troubleshooting or dispatch a replacement unit for critical breakdown situations.
📝 From the Field: Australian Farmers Review the Flail Mower Gearbox
Our agricultural gearboxes are field-proven across every Australian state and territory. Below are documented case studies from recent Flail Mower gearbox installations.
📍 Case #1: Mackay, QLD
| Klient: |
Derek Whitfield — commercial grass cutting contractor |
| Lokalizacja: |
Mackay, QLD |
| Wielkość gospodarstwa: |
3500 acres |
| Aplikacja: |
Flail Mower gearbox for flail mower — grass cutting |
| Powód zakupu: |
Replace failed OEM gearbox to restore flail mower for the upcoming season |
“Our flail mower operates in extremely dusty conditions and we were going through gearboxes every season. This one has survived 4 seasons and is still running perfectly. The sealing is clearly superior to what we had before.”
— Derek Whitfield, Mackay, QLD
Jack Thornton — Mildura, VIC
Działanie: cooperative farming group | Rozmiar: 1000 acres | Używać: Flail Mower gearbox for grass cutting
Powód zakupu: Emergency mid-season replacement after catastrophic original gearbox failure
“Quality comparable to European OEM units at half the price point. The machining is clean, the paint is durable, and the gears are noticeably smoother than the Chinese-made unit it replaced. Recommended to three other farmers already.”
📍 Griffith, NSW commercial grass cutting contractor — 8000 acres
Klient: Luke Anderson | Aplikacja: Flail Mower gearbox — grass cutting
Zamiar: Budowa nowego sprzętu — określenie skrzyni biegów na rynku wtórnym jako ulepszenia OEM
“We stress-test our equipment in ways that would void most warranties. This gearbox has handled everything we’ve thrown at it — continuous 12-hour shifts — without complaint.”
📍 Case #4: Hamilton, VIC
| Klient: |
Terry Voss — broadacre cropping operation |
| Lokalizacja: |
Hamilton, VIC |
| Wielkość gospodarstwa: |
1000 acres |
| Aplikacja: |
Flail Mower gearbox for flail mower — grass cutting |
| Powód zakupu: |
Retrofit older model flail mower with improved gearbox for extended service life |
“The oil-tight sealing on this gearbox is remarkable. After 1611 hours of operation in muddy conditions, the oil comes out clean at service time. Previous gearboxes always had contaminated oil by the first oil change.”
— Terry Voss, Hamilton, VIC
Ed Pearce — Melbourne, VIC
Działanie: intensive horticultural farm | Rozmiar: 4000 acres | Używać: Flail Mower gearbox for grass cutting
Powód zakupu: Modernizacja niedrogiego urządzenia z rynku wtórnego, które wytrzymało mniej niż jeden sezon
„Opcja niestandardowych proporcji była przełomem dla naszej działalności. Potrzebowaliśmy niestandardowej prędkości wyjściowej, której żaden inny dostawca nie mógł zapewnić. Zespół inżynierów zaprojektował rozwiązanie w ciągu tygodnia i działało ono idealnie od pierwszego dnia”.
❓ Flail Mower Gearbox FAQ — Everything You Need to Know
🔹 Do you provide technical support after purchase?
Tak — każdy zakup obejmuje dostęp do naszego zespołu wsparcia technicznego, który udziela wskazówek dotyczących instalacji, rozwiązywania problemów, udziela porad dotyczących konserwacji i zamawiania części. Wsparcie jest dostępne telefonicznie, mailowo i za pośrednictwem naszego formularza kontaktowego online. Wsparcie techniczne jest bezpłatne w okresie gwarancyjnym i po jego zakończeniu.
🔹 What documentation ships with the gearbox?
Każda skrzynia biegów dostarczana jest z: instrukcją montażu zawierającą dane dotyczące momentu obrotowego, harmonogramem smarowania i konserwacji, schematem części z numerami poszczególnych części, kartą gwarancyjną oraz certyfikatem kontroli jakości zawierającym numer seryjny urządzenia i wyniki testów.
🔹 Can this gearbox withstand the shock loads generated during grass cutting?
The gearbox is specifically designed for the dynamic and impact loading characteristic of grass cutting applications. Case-hardened alloy steel gears absorb repetitive shocks, while the optional overload protection (shear bolt or slip clutch) safeguards against catastrophic overload events. The bearing selection and housing rigidity are both matched to flail mower load profiles.
🔹 What does the warranty cover and for how long?
Our 24-month comprehensive warranty covers all defects in materials and workmanship, including bearings, gears, seals, and housing. It applies from the date of purchase and is backed by our ISO-certified quality management system. Extended warranty programs are available for bulk and fleet orders.
🔹 Which gear oil do you recommend for Australian conditions?
For most Australian climates, SAE 80W-90 EP gear oil meeting GL-5 specification is ideal. In tropical regions with sustained high temperatures, we recommend 85W-140. For southern regions experiencing cold winters, synthetic 75W-90 provides better cold-start protection. Check the oil specification card shipped with your gearbox for the definitive recommendation.
🔹 Can I return a gearbox if it does not fit my flail mower?
If you provide your equipment details before ordering and we confirm compatibility, fitment is guaranteed. In the rare event of a compatibility issue, we offer a no-questions-asked exchange or refund on unused gearboxes within 30 days of delivery. Our goal is to match you with the correct gearbox on the first order.
🔹 Is the gearbox suitable for use in organic-certified farming operations?
Nasze przekładnie są elementami mechanicznymi i nie zawierają substancji, które mogłyby wpłynąć na certyfikację ekologiczną. Należy jednak rozważyć wybór środka smarnego — możemy polecić biodegradowalne oleje przekładniowe o jakości spożywczej, zgodne ze standardami rolnictwa ekologicznego obowiązującymi w Australii i na świecie.
🔹 Can the gearbox be serviced or rebuilt in the field?
Rutynowe przeglądy (wymiana oleju, wymiana uszczelnień, kontrola łożysk) mogą być wykonywane na miejscu, przy użyciu standardowych narzędzi. W przypadku większych remontów dostarczamy kompletne zestawy naprawcze zawierające wszystkie łożyska, uszczelnienia i podkładki. Szczegółowe instrukcje serwisowe i przewodniki wideo są dostępne do pobrania z naszego portalu wsparcia.
🔹 What payment and ordering options do you offer?
Akceptujemy przelewy bankowe, karty kredytowe oraz zamówienia z kont bankowych. W przypadku dużych zamówień oferujemy 30-dniowy termin płatności, po uzyskaniu pozytywnej decyzji kredytowej. Zamówienia można składać za pośrednictwem naszej strony internetowej, mailowo lub telefonicznie. W przypadku płatności z góry dostępne są faktury proforma.
🔹 Can the output shaft be customized for my specific flail mower?
Absolutely. We manufacture gearboxes with keyed, splined, flanged, hex, and hollow-bore output shaft configurations. If your flail mower requires a non-standard output size, spline count, or connection type, our engineering team will design and machine it to your exact specifications at no additional lead time for common modifications.
⚙ Build a Reliable Grass Cutting Powertrain
These products are frequently purchased alongside our Flail Mower gearbox by Australian farmers optimizing their grass cutting equipment.
PTO Drive Shaft for Flail Mower
Rugged PTO drive shafts built for grass cutting demands. Standard, wide-angle, and CV joint options. Telescoping tube with nylon liner. Full guard kit included.
View PTO Shafts →
Explore Our Gearbox Range
Multi-machine operators benefit from our comprehensive gearbox catalogue — standardised quality, consolidated shipping, and volume pricing across the full range.
Browse Gearboxes →
⚖ Safety Standards for Flail Mower Equipment in Australia
Operating flail mower equipment in Australia requires compliance with federal and state workplace health and safety legislation. Key requirements for Flail Mower gearbox installations include:
Standards Compliance
| Standard |
Relevance |
| AS/NZS ISO 9001:2015 — Quality Management |
Our manufacturing facility holds current certification to the international quality management standard. |
| AS 1636 — Agricultural Machinery Safety |
Our gearboxes meet design requirements for agricultural machinery components, including rotating part guarding interfaces. |
| Safe Work Australia PTO Safety Guidelines |
All PTO-driven flail mower equipment must incorporate compliant shaft guarding. Guard-compatible drivelines available. |
State-Level WHS Requirements
- Terytorium Północne — Przepisy WHS (jednolite ustawodawstwo krajowe) z 2011 r.: applies federal standards to grass cutting operations territory-wide.
- South Australia — WHS Regulations 2012: requires regular inspection of all machinery with rotating drive components.
- Tasmania — Przepisy WHS 2012: mandates operator training for all PTO-driven flail mower equipment.
Zasięg regionalny i sieć dostaw
Dostarczamy Flail Mower agricultural gearboxes to every state and territory in Australia. Our logistics network covers major farming regions including the North West Slopes, Hunter Valley, and Central West NSW, the Barossa Valley, the Riverland, and South East SA, and the Riverina, the Murrumbidgee Irrigation Area, and the Liverpool Plains. Whether you operate in a metropolitan fringe area or a remote pastoral station, we ship directly to your property with full tracking and delivery confirmation.
🎯 Your Flail Mower Gearbox Journey Starts Here
With over two decades of experience and 150,000+ gearboxes produced each year, we are one of the most established agricultural gearbox manufacturers serving the Australian market. Our production capabilities include: cmm (coordinate measuring machine) dimensional inspection, precision cnc gear cutting and grinding with sub-micron repeatability, iso 9001:2015 certified quality management with full batch traceability, and much more.
Standard & Custom — We Build Both
Standard specifications don’t always fit. Our engineering team designs and manufactures custom gearboxes to your drawings, samples, or specifications. From modified OEM replacements to completely new designs for specialised flail mower equipment — we handle it all.
Drawings, samples, dimensions, photos — whatever you have, send it. We will engineer the rest.
🏭 Discover Our Full Capabilities →
Twój zaufany partner w zakresie rozwiązań dla skrzyń biegów w maszynach rolniczych — standardowych i niestandardowych — w Australii i na całym świecie.
