EP-RTD50 Rotary Tiller Gearbox

EP-RTD50 Rotary Tiller Gearbox

As a center-drive gearbox for rotary tillers, the EP-RTD50 distributes 50 HP evenly to left and right tiller rotor sections. Broadacre tillage operators and commercial cultivation services select this model for its balanced power delivery, precision flange alignment, and extended 500-hour oil change intervals.

商品コード: 427d10ca2d08 カテゴリー: タグ: , , , ,

説明


EP-RTD50 — The Operator’s Choice in Rotary Tiller Center Gearbox Technology

Trusted by professional farmers and contractors worldwide, the EP-RTD50 芝刈り機のギアボックス combines 50馬力 capacity with robust 25 Kg (approx.) cast construction. Available in N/A ratio configurations, it adapts to your mowing conditions with ease.

EP-RTD50 Rotary Tiller Center Gearbox

📈 EP-RTD50 Technical Specifications

パラメータ 仕様
型番 EP-RTD50
ギアボックスタイプ ロータリーティラーセンターギアボックス
ギア比 N/A
歯の形状 N/A
ギアモジュール N/A
定格電力 50馬力
入力速度 540回転/分
入力/出力シャフト Flange mount
正味重量 25 Kg (approx.)
ギア素材 20CrMnTi合金鋼、浸炭焼入れ済み、硬度HRC 58-62
ハウジング材 ねずみ鋳鉄（HT200/HT250）
シール保護 マルチリップNBR/FKMオイルシール、IP65+規格準拠
潤滑 SAE 80W-90または85W-140 EPギアオイル
表面処理 Eコートプライマー＋ポリエステル粉体塗装、赤色仕上げ

⭐ 主な特長とエンジニアリング上の利点

⚖

Hot-Dip Galvanized Mounting Hardware

Grade 10.9 mounting bolts hot-dip galvanized to AS/NZS 4680, resisting corrosion in coastal and high-humidity farming regions like northern Queensland and Waikato.

🚀

Field-Rebuildable Modular Design

All internal components — gears, bearings, seals, shafts — are individually replaceable in the field with standard hand tools, eliminating the need to send units away for factory rebuild.

💪

Dual-Lip NBR Oil Seals

Twin-lip nitrile seals with integrated dust excluder on every shaft exit, rated to IP65, preventing moisture and crop debris from entering the gear chamber.

⚙

Optimized Lightweight Geometry

Finite-element-optimized casing walls remove unnecessary material while maintaining full load capacity, reducing installed weight by 15% versus previous-generation housings.

⚗

20CrMnTi Forged Gear Blanks

All gear blanks are closed-die forged (not cast) to align grain flow with tooth roots, increasing bending fatigue strength by 30% over alternative casting methods.

🔒

97%+ Mechanical Efficiency Rating

Super-finished gear flanks (Ra ≤ 0.6 μm) and optimized tooth contact deliver over 97% efficiency, reducing fuel consumption and allowing cooler continuous operation.

農業用芝刈り機のギアボックス

🔧 機器の互換性と相互参照

🔄 Cross-Reference Compatibility for EP-RTD50

The EP-RTD50 is engineered as a direct replacement or upgrade for gearboxes fitted to equipment from leading manufacturers including:

Pöttinger • TAFE • McCormick • Mitsubishi • Zoomlion • Case IH • Land Pride • Mahindra

免責事項：上記のブランド名は、互換性確認のためのみに記載されています。Ever-power Australia Mower Gearbox Co.,Ltd.は、記載されているメーカーとは一切提携、承認、または認可を受けていません。すべての商標は、それぞれの所有者に帰属します。

📚 ギアボックス選定ガイド

Getting gearbox selection right the first time saves money and headaches. Here is a systematic approach to specifying the EP-RTD50:

📌 Cast Iron Housing vs Aluminium Housing
The EP-RTD50 uses a grey cast iron housing. Cast iron excels in vibration damping, impact resistance, and heat dissipation — ideal for rough, rocky mowing conditions. Aluminium is lighter and more corrosion-resistant, better suited to wet environments and weight-sensitive implements.
📌 標準カタログ vs カスタム仕様
The EP-RTD50 is available as a standard catalog item shipping in 3-5 days. If your application requires a non-standard ratio, shaft type, or mounting configuration, our engineering team offers custom designs with 4-6 week lead times. Minimum order quantities may apply.
📌出力軸タイプの互換性
The EP-RTD50 features Flange mount output. Verify your blade hub or implement rotor accepts this shaft type before ordering. We offer multiple output configurations — spline, taper, keyway, and flange — to match virtually any existing installation.
📌重量と取り付けに関する考慮事項
At 25 Kg (approx.), the EP-RTD50 is designed for rotary tiller frames and cultivation equipment. Confirm your implement frame and three-point hitch can support this weight plus the weight of the blade assembly. Mounting bolt pattern and orientation should match your existing layout.
📌 ギア比とブレード先端速度のマッチング
For the EP-RTD50 with ratio(s) N/A, calculate your required blade tip speed: typically 4,500-5,500 m/min for standard rotary cutters, 3,000-4,000 m/min for heavy brush cutting, and 5,500-6,500 m/min for fine finish mowing. Output RPM = PTO RPM ÷ ratio. Multiply by blade diameter to get tip speed.

🌾 一般的なアプリケーションシナリオ

🌾 Pipeline and powerline easement clearing

🚘 Riparian zone and waterway bank vegetation control

🌱 Rotary tiller seedbed preparation for row crops

⛰ Land clearing of light to medium regrowth scrub

🌳 Hay field pre-cut conditioning and topping

エバーパワー・オーストラリア・モアギアボックス株式会社の製造施設

🛠 インストールとセットアップガイド

  1. Record the installation date, tractor hour meter reading, and gearbox serial number in your maintenance log for warranty and service interval tracking.
  2. If replacing an existing unit, drain the old oil completely, remove mounting fasteners, and carefully lower the old gearbox. Photograph the orientation and note any shim washers used.
  3. Insert all mounting bolts finger-tight first, then torque to specification in a cross (star) pattern to ensure even clamping. Typical torque: 80-120 Nm depending on bolt size.
  4. With the implement raised and blades clear of the ground, engage the PTO at low idle speed. Listen for any unusual noise and observe for vibration or oil leaks.
  5. Verify that the mower implement safety chain or restraint is properly connected to prevent the gearbox from contacting the ground if the three-point hitch fails.
  6. Apply a thin, even bead of RTV silicone sealant to the mounting flange face if a pre-cut gasket is not included with the new gearbox.
  7. Connect the PTO drive shaft to the gearbox input spline. Push the shaft on fully and verify it telescopes freely through the complete range of three-point hitch travel.

❓よくある質問

❓ What warranty do you provide?

Every gearbox ships with a 12-month warranty covering material and workmanship defects under normal operating conditions. Warranty claims are handled through our dealer network with replacement units dispatched within 48 hours of approval.

❓ How do I determine the correct model for my mower?

You need four pieces of information: (1) tractor PTO HP, (2) PTO speed (540 or 1000 RPM), (3) current gearbox mounting dimensions, and (4) output shaft type. Send us these details and we will cross-reference the best match.

❓ Is synthetic gear oil recommended?

Synthetic PAO-based 75W-90 or 80W-140 GL-5 oil is excellent, especially in extreme temperatures. Synthetics offer better cold-flow, higher film strength, and longer drain intervals. Fully compatible with all our seal materials.

❓ What shipping methods are available?

Sea freight (20-35 days), air freight (5-10 days), and express courier (3-5 days) worldwide. Sea freight is most economical for bulk orders. All shipments include protective packaging, documentation, and full tracking.

❓ Can this unit directly replace my OEM gearbox?

Yes. Our mounting patterns, shaft diameters, and spline profiles match industry-standard OEM dimensions. We supply detailed technical drawings for cross-referencing. If your existing unit differs slightly, our engineering team can advise on adapters.

⭐ お客様の声と現場レポート

★★★★★

📍 Western Australia, Australia

Runs noticeably cooler than the old gearbox it replaced. The improved cooling design and better oil volume are making a real difference.

★★★★★

📍 São Paulo, Brazil

競合他社製品と並べてテストした結果、本製品はより静かに作動し、発熱も少なく、200時間以上使用してもオイルが汚れずにきれいな状態を保っていました。

★★★★★

📍 Skåne, Sweden

このメーカーから初めて購入しましたが、大変満足しています。製品の品質、説明書、サポート、すべてが最高レベルでした。

★★★★☆

📍 Alentejo, Portugal

5つのブランドの仕様を比較した結果、素材、重量、価格のバランスが最も優れていたのがこの製品でした。後悔は全くありません。

★★★★☆

📍 Canterbury, New Zealand

Fitted to my pasture topper last season. Over 400 hours and counting — zero leaks, minimal noise. Excellent value for a professional-grade unit.

農業用ギアボックスシリーズ

⚖ EP-RTD50 vs. Low-Cost Alternatives

特徴 EP-RTD50 (Ever-power) ジェネリック／低価格代替品
Engineering Support ✔ Free Application Engineering & Cross-Reference ✘ No Technical Support Provided
Oil Seals ✔ Double-Lip NBR/FKM, IP65 Rated ✘ Single-Lip NBR, No Dust Lip
Dimensional Tolerance ✔ ISO IT6-IT7, CNC Machined Throughout ✘ ISO IT9-IT10, Partially Hand-Finished
Documentation ✔ Full Drawings, Cross-Reference, Install Guide ✘ Basic Single-Page Spec Sheet Only
Fastener Protection ✔ Zinc-Flake Coated Grade 10.9 Bolts ✘ Plain Steel Grade 8.8, Corrodes and Seizes
Oil Level Check ✔ Clear Sight Glass + Dipstick Standard ✘ No Sight Glass, Must Remove Fill Plug
After-Sales Support ✔ Dedicated Technical Team, Video Call Support ✘ Email Only, 1-2 Week Response Time

🔄関連商品・アクセサリー

🏆 認証と品質基準

Our production of the EP-RTD50 follows ISO 9001:2015 requirements with additional internal standards that exceed baseline certification. Key processes include: 100% CMM dimensional verification, Vickers hardness mapping on every gear, hydrostatic housing leak test at 1.5× rated pressure, and a 15-minute no-load run-in test. Test reports accompany every shipment.

🏭 Ever-power Australia Mower Gearbox Co.,Ltd.を選ぶ理由とは？

What sets Ever-power Australia Mower Gearbox Co.,Ltd. apart is our ability to scale seamlessly from engineering support for a single unique application to mass production of 78000+ units per year without any compromise in quality. Our 11 gear production lines, climate-controlled metrology lab, and experienced technical sales team work together to make your sourcing process as efficient as your fieldwork needs to be.

PTO駆動シャフト

📞 Get Your EP-RTD50 Quote Today

Stop losing field time to gearbox failures. The EP-RTD50 is built to run all season without skipping a beat. Talk to our specialists about the right configuration for your operation.

見積もりを依頼する全商品を見る

関連商品