EP-68 Degree Angle Lawn Mower Gearbox

EP-68 Degree Angle Lawn Mower Gearbox

Unlike standard 90-degree gearboxes, the EP-68 transmits power at a 68-degree shaft angle with a 1:1 ratio. Specialty implement builders and steep-terrain mowing contractors use this unique angle to position blades closer to embankments, levee walls, and ditch slopes that perpendicular drives cannot reach.

Artikelnummer: 904769ee807e Categorie: Tags: , , , ,

Beschrijving


EP-68 — The Operator’s Choice in 68-Degree Angle Gearbox Technology

Trusted by professional farmers and contractors worldwide, the EP-68 versnellingsbak van de maaier combines 30 HP capacity with robust 13.2 Kg cast construction. Available in 1:1 ratio configurations, it adapts to your mowing conditions with ease.

EP-68 68-Degree Angle Gearbox

📈 EP-68 Technical Specifications

Parameter Specificatie
Modelnummer EP-68
Versnellingsbaktype 68-Degree Angle Gearbox
Overbrengingsverhouding(en) 1:1
Tandconfiguratie 19/19
Tandwielmodule 4.23
Nominaal vermogen 30 HP
Invoersnelheid 540 toeren per minuut
Invoer-/uitvoeras Optic axis / Spline
Nettogewicht 13.2 Kg
Tandwielmateriaal 20CrMnTi gelegeerd staal, gecarburiseerd en gehard HRC 58-62
Behuizingsmateriaal Grijs gietijzer (HT200/HT250)
Verzegeling Bescherming Meervoudige NBR/FKM-oliekeerringen, IP65+-geclassificeerd
Smering SAE 80W-90 of 85W-140 EP tandwielolie
Oppervlaktebehandeling E-coat primer + polyester poedercoating, rode afwerking

⭐ Belangrijkste kenmerken en technische voordelen

🛠

Self-Contained Bearing Cartridges

Pre-loaded, pre-lubricated cartridge bearings drop in for rapid field replacement, slashing unplanned downtime from bearing failures by up to 70%.

🔬

Synthetic PAO Fill, -40 to +150 °C

Factory-filled with polyalphaolefin gear oil maintaining viscosity stability from arctic cold starts to sustained high-temperature tropical operation without degradation.

⚖

Through-Hardened Spur Gear Train

HRC 56-60 alloy steel spur gears designed for the high-impact reversing loads encountered during aggressive rotary tiller soil engagement.

🚀

3× Peak Torque Output Capacity

Oversized output shaft rated for transient torques three times nominal, absorbing the repeated shock loads when tiller blades strike buried rocks and roots.

💪

500-Hour Extended Oil Intervals

Large sump capacity with high-grade EP oil enables 500-hour drain intervals, reducing maintenance frequency during the busiest planting and cultivation seasons.

⚙

Oil-Bath Splash Lubrication

Generous sump with directional baffles ensures all gear teeth and bearing races are oil-wetted at all times, even at the lowest recommended operating speed.

Mower gearbox in agricultural use

🔧 Compatibiliteit en kruisverwijzing van apparatuur

🔄 Cross-Reference Compatibility for EP-68

The EP-68 is engineered as a direct replacement or upgrade for gearboxes fitted to equipment from leading manufacturers including:

Krone • McConnel • Fendt • Iseki • YTO • Massey Ferguson • Deutz-Fahr • Woods

Disclaimer: De bovenstaande merknamen worden uitsluitend vermeld ter identificatie van de compatibiliteit. Ever-power Australia Mower Gearbox Co.,Ltd. is niet gelieerd aan, onderschreven door of geautoriseerd door een van de vermelde fabrikanten. Alle handelsmerken behoren toe aan hun respectievelijke eigenaren.

📚 Gids voor het kiezen van een versnellingsbak

Getting gearbox selection right the first time saves money and headaches. Here is a systematic approach to specifying the EP-68:

📌 Gietijzeren behuizing versus aluminium behuizing
The EP-68 uses a grey cast iron housing. Cast iron excels in vibration damping, impact resistance, and heat dissipation — ideal for rough, rocky mowing conditions. Aluminium is lighter and more corrosion-resistant, better suited to wet environments and weight-sensitive implements.
📌 Standaardcatalogus versus specificaties op maat
The EP-68 is available as a standard catalog item shipping in 3-5 days. If your application requires a non-standard ratio, shaft type, or mounting configuration, our engineering team offers custom designs with 4-6 week lead times. Minimum order quantities may apply.
📌 Output Shaft Type Compatibility
The EP-68 features Optic axis / Spline output. Verify your blade hub or implement rotor accepts this shaft type before ordering. We offer multiple output configurations — spline, taper, keyway, and flange — to match virtually any existing installation.
📌 Weight and Mounting Considerations
At 13.2 Kg, the EP-68 is designed for specialty mounting configurations. Confirm your implement frame and three-point hitch can support this weight plus the weight of the blade assembly. Mounting bolt pattern and orientation should match your existing layout.
📌 Afstemming van de overbrengingsverhouding op de snelheid van de bladpunt
For the EP-68 with ratio(s) 1:1, calculate your required blade tip speed: typically 4,500-5,500 m/min for standard rotary cutters, 3,000-4,000 m/min for heavy brush cutting, and 5,500-6,500 m/min for fine finish mowing. Output RPM = PTO RPM ÷ ratio. Multiply by blade diameter to get tip speed.

🌾 Typische toepassingsscenario's

🌾 Construction site vegetation clearing and preparation

🚘 Roadside and highway verge vegetation management

🌱 Pipeline and powerline easement clearing

⛰ Riparian zone and waterway bank vegetation control

🌳 Rotary tiller seedbed preparation for row crops

Ever-power Australia Mower Gearbox Co.,Ltd. manufacturing facility

🛠 Installatie- en configuratiehandleiding

  1. Koppel de aftakas van de tractor los en ondersteun het maaiwerktuig veilig met krikken of blokken voordat u begint met de installatie van de versnellingsbak.
  2. Voor units die meer dan 25 kg wegen, gebruik een kettingtakel, motortakel of een hijsinstallatie met twee personen om de versnellingsbak te positioneren. Probeer nooit zware versnellingsbakken in je eentje te tillen.
  3. Vul de versnellingsbak bij met de aanbevolen versnellingsbakolie (SAE 80W-90 of 85W-140 EP) tot het niveau dat is aangegeven op het kijkglas of de peilstok. Niet te veel bijvullen.
  4. Voordat u op vol vermogen gaat werken, doorloop een geleidelijke inloopperiode: 30 minuten op half gas, vervolgens 30 minuten op driekwart gas, voordat u het volledige aftakastoerental inschakelt.
  5. Controleer met een liniaal of de montageplaat van het werktuig vlak is. Eventuele krommingen van meer dan 0,5 mm moeten worden gecorrigeerd voordat de nieuwe versnellingsbak wordt gemonteerd.
  6. Gebruik Nord-Lock-ringen of schroefdraadborgmiddel op alle bevestigingsbouten om losraken door trillingen tijdens gebruik te voorkomen.
  7. Run the gearbox at no load for 5-10 minutes, then shut down and re-check oil level — new seals and bearings often absorb a small amount of initial oil.

❓ Veelgestelde vragen

❓ Is this suitable for mulching applications?

Yes. Our gearboxes are widely used on mulching mowers and brush cutters. For mulching, select a model rated 25-30% above your actual PTO horsepower to provide a safety margin against the intermittent shock loads typical of mulching.

❓ What quality inspections do you perform?

Every gearbox undergoes 100% dimensional inspection (CMM), gear tooth geometry verification (Gleason analyzer), hardness testing, oil-leak testing, and no-load run-in testing before shipment.

❓ What warranty do you provide?

Every gearbox ships with a 12-month warranty covering material and workmanship defects under normal operating conditions. Warranty claims are handled through our dealer network with replacement units dispatched within 48 hours of approval.

❓ How do I determine the correct model for my mower?

You need four pieces of information: (1) tractor PTO HP, (2) PTO speed (540 or 1000 RPM), (3) current gearbox mounting dimensions, and (4) output shaft type. Send us these details and we will cross-reference the best match.

❓ Is synthetic gear oil recommended?

Synthetic PAO-based 75W-90 or 80W-140 GL-5 oil is excellent, especially in extreme temperatures. Synthetics offer better cold-flow, higher film strength, and longer drain intervals. Fully compatible with all our seal materials.

⭐ Klantenrecensies en praktijkverslagen

★★★★★

📍 New South Wales, Australia

Replaced a failed OEM unit on a 15-year-old mower. This new gearbox is actually smoother and quieter than the original ever was.

★★★★★

📍 Hokkaido, Japan

Best aftermarket unit I have used in 20+ years of farming. Bolt holes aligned first try. Oil sight glass is a thoughtful touch.

★★★★★

📍 Castilla, Spain

Precision manufacturing is evident when you look at the gear teeth. Mesh noise is minimal. Very satisfied with this purchase.

★★★★☆

📍 Mendoza, Argentina

The compact size was critical for our application and this model delivered. Two years running, zero problems whatsoever.

★★★★☆

📍 Bavaria, Germany

We ordered in bulk for our dealer network. Customer return rate is near zero. That speaks volumes about reliability.

Agricultural gearbox range

⚖ EP-68 vs. Low-Cost Alternatives

Functie EP-68 (Ever-power) Generiek / Goedkoop alternatief
Traceerbaarheid ✔ Lasergeëtst serienummer, volledige materiaalregistratie ✘ Geen serienummer, geen traceerbaarheid
Behuizingsbewerking ✔ 5-assige CNC, IT6-boringstolerantie ✘ 3-assige CNC of handmatige bewerking, IT9-boringstolerantie
Beschikbaarheid van reserveonderdelen ✔ Full Inventory, Ships Within 24 Hours ✘ Limited Stock, 4-8 Week Back-Order
Lead Time ✔ 3-5 Days Standard, 4-6 Weeks Custom ✘ 8-12 Weeks, No Expedite Option
Gear Accuracy ✔ AGMA Class 8-10, CNC Ground Post Heat-Treatment ✘ AGMA Class 5-6, Hobbed Only, No Grinding
Oil Capacity ✔ Generous Sump for Extended Cooling, Sight Glass ✘ Minimal Oil Volume, No Level Indicator
Aftapplug ✔ Magnetische plug vangt slijtagepartikels op ✘ Standaard stekker, geen deeltjesopvang

🔄 Related Products & Accessories

🏆 Certifications & Quality Standards

Our production of the EP-68 follows ISO 9001:2015 requirements with additional internal standards that exceed baseline certification. Key processes include: 100% CMM dimensional verification, Vickers hardness mapping on every gear, hydrostatic housing leak test at 1.5× rated pressure, and a 15-minute no-load run-in test. Test reports accompany every shipment.

🏭 Why Choose Ever-power Australia Mower Gearbox Co.,Ltd.?

What sets Ever-power Australia Mower Gearbox Co.,Ltd. apart is our ability to scale seamlessly from engineering support for a single unique application to mass production of 64000+ units per year without any compromise in quality. Our 9 gear production lines, climate-controlled metrology lab, and experienced technical sales team work together to make your sourcing process as efficient as your fieldwork needs to be.

PTO drive shaft

📞 Get Your EP-68 Quote Today

Stop losing field time to gearbox failures. The EP-68 is built to run all season without skipping a beat. Talk to our specialists about the right configuration for your operation.

Request a QuoteBrowse All Products

Gerelateerde producten