Keterangan
EP-68 — The Operator’s Choice in 68-Degree Angle Gearbox Technology
Trusted by professional farmers and contractors worldwide, the EP-68 girboks mesin pemotong rumput combines 30 HP capacity with robust 13.2 Kg cast construction. Available in 1:1 ratio configurations, it adapts to your mowing conditions with ease.
📈 EP-68 Technical Specifications
| Parameter | Spesifikasi |
|---|---|
| Nomor Model | EP-68 |
| Jenis Gearbox | 68-Degree Angle Gearbox |
| Rasio Gigi | 1:1 |
| Konfigurasi Gigi | 19/19 |
| Modul Gigi | 4.23 |
| Daya Terukur | 30 HP |
| Kecepatan Masukan | 540 rpm |
| Poros Masukan/Keluaran | Optic axis / Spline |
| Berat Bersih | 13.2 Kg |
| Bahan Roda Gigi | Baja Paduan 20CrMnTi, Dikarburisasi & Dikeraskan HRC 58-62 |
| Bahan Perumahan | Besi Cor Abu-abu (HT200/HT250) |
| Perlindungan Segel | Segel Oli Multi-Bibir NBR/FKM, Peringkat IP65+ |
| Pelumasan | Oli roda gigi SAE 80W-90 atau 85W-140 EP |
| Perawatan Permukaan | Primer E-Coat + Lapisan Serbuk Poliester, Warna Merah |
⭐ Fitur Utama & Keunggulan Teknik
🛠
Self-Contained Bearing Cartridges
Pre-loaded, pre-lubricated cartridge bearings drop in for rapid field replacement, slashing unplanned downtime from bearing failures by up to 70%.
🔬
Synthetic PAO Fill, -40 to +150 °C
Factory-filled with polyalphaolefin gear oil maintaining viscosity stability from arctic cold starts to sustained high-temperature tropical operation without degradation.
⚖
Through-Hardened Spur Gear Train
HRC 56-60 alloy steel spur gears designed for the high-impact reversing loads encountered during aggressive rotary tiller soil engagement.
🚀
3× Peak Torque Output Capacity
Oversized output shaft rated for transient torques three times nominal, absorbing the repeated shock loads when tiller blades strike buried rocks and roots.
💪
500-Hour Extended Oil Intervals
Large sump capacity with high-grade EP oil enables 500-hour drain intervals, reducing maintenance frequency during the busiest planting and cultivation seasons.
⚙
Oil-Bath Splash Lubrication
Generous sump with directional baffles ensures all gear teeth and bearing races are oil-wetted at all times, even at the lowest recommended operating speed.
🔧 Kompatibilitas dan Referensi Silang Peralatan
🔄 Cross-Reference Compatibility for EP-68
The EP-68 is engineered as a direct replacement or upgrade for gearboxes fitted to equipment from leading manufacturers including:
Krone • McConnel • Fendt • Iseki • YTO • Massey Ferguson • Deutz-Fahr • Woods
Penafian: Nama merek di atas hanya dirujuk untuk identifikasi kompatibilitas. Ever-power Australia Mower Gearbox Co.,Ltd. tidak berafiliasi dengan, didukung oleh, atau diotorisasi oleh produsen mana pun yang tercantum. Semua merek dagang milik pemiliknya masing-masing.
📚 Panduan Pemilihan Transmisi
Getting gearbox selection right the first time saves money and headaches. Here is a systematic approach to specifying the EP-68:
🌾 Skenario Aplikasi Umum
🌾 Construction site vegetation clearing and preparation
🚘 Roadside and highway verge vegetation management
🌱 Pipeline and powerline easement clearing
⛰ Riparian zone and waterway bank vegetation control
🌳 Rotary tiller seedbed preparation for row crops
🛠 Panduan Instalasi & Pengaturan
- Disconnect the tractor PTO shaft and safely support the mower implement on jack stands or blocks before beginning the gearbox installation procedure.
- For units weighing over 25 kg, use a chain hoist, engine crane, or two-person lift to position the gearbox. Never attempt to lift heavy gearboxes solo.
- Fill the gearbox with the recommended gear oil (SAE 80W-90 or 85W-140 EP) to the level indicated on the sight glass or dipstick. Do not overfill.
- Before operating at full load, run through a graduated break-in sequence: 30 minutes at half-throttle, then 30 minutes at three-quarter throttle, before engaging full PTO speed.
- Inspect the implement mounting pad for flatness using a straightedge. Any warping exceeding 0.5 mm should be corrected before the new gearbox is installed.
- Use Nord-Lock washers or thread-locking compound on all mounting bolts to prevent vibration-induced loosening during operation.
- Run the gearbox at no load for 5-10 minutes, then shut down and re-check oil level — new seals and bearings often absorb a small amount of initial oil.
❓ Pertanyaan yang Sering Diajukan
⭐ Ulasan Pelanggan & Laporan Lapangan
Bruce K.
★★★★★
📍 New South Wales, Australia
Mengganti unit OEM yang rusak pada mesin pemotong rumput berusia 15 tahun. Gearbox baru ini sebenarnya lebih halus dan lebih senyap daripada yang asli.
Kenji T.
★★★★★
📍 Hokkaido, Japan
Ini adalah unit aftermarket terbaik yang pernah saya gunakan selama lebih dari 20 tahun bertani. Lubang baut sejajar pada percobaan pertama. Kaca pengintai oli adalah sentuhan yang sangat bermanfaat.
Javier R.
★★★★★
📍 Castilla, Spain
Precision manufacturing is evident when you look at the gear teeth. Mesh noise is minimal. Very satisfied with this purchase.
Roberto C.
★★★★☆
📍 Mendoza, Argentina
The compact size was critical for our application and this model delivered. Two years running, zero problems whatsoever.
Hans B.
★★★★☆
📍 Bavaria, Germany
We ordered in bulk for our dealer network. Customer return rate is near zero. That speaks volumes about reliability.
⚖ EP-68 vs. Low-Cost Alternatives
| Fitur | EP-68 (Ever-power) | Alternatif Generik / Murah |
|---|---|---|
| Traceability | ✔ Laser-Etched Serial, Full Material Records | ✘ No Serial Number, No Traceability |
| Housing Machining | ✔ 5-Axis CNC, IT6 Bore Tolerance | ✘ 3-Axis CNC or Manual, IT9 Bore Tolerance |
| Spare Parts Availability | ✔ Full Inventory, Ships Within 24 Hours | ✘ Limited Stock, 4-8 Week Back-Order |
| Lead Time | ✔ 3-5 Days Standard, 4-6 Weeks Custom | ✘ 8-12 Weeks, No Expedite Option |
| Gear Accuracy | ✔ AGMA Class 8-10, CNC Ground Post Heat-Treatment | ✘ AGMA Class 5-6, Hobbed Only, No Grinding |
| Oil Capacity | ✔ Generous Sump for Extended Cooling, Sight Glass | ✘ Minimal Oil Volume, No Level Indicator |
| Drain Plug | ✔ Magnetic Plug Captures Wear Particles | ✘ Standard Plug, No Particle Capture |
🔄 Related Products & Accessories
Browse our complete range of agricultural transmission components including PTO shafts, gears, pulleys, chains, and sprockets — all engineered to integrate seamlessly with EP-68 gearboxes.
🏆 Certifications & Quality Standards
Our production of the EP-68 follows ISO 9001:2015 requirements with additional internal standards that exceed baseline certification. Key processes include: 100% CMM dimensional verification, Vickers hardness mapping on every gear, hydrostatic housing leak test at 1.5× rated pressure, and a 15-minute no-load run-in test. Test reports accompany every shipment.
🏭 Why Choose Ever-power Australia Mower Gearbox Co.,Ltd.?
What sets Ever-power Australia Mower Gearbox Co.,Ltd. apart is our ability to scale seamlessly from engineering support for a single unique application to mass production of 64000+ units per year without any compromise in quality. Our 9 gear production lines, climate-controlled metrology lab, and experienced technical sales team work together to make your sourcing process as efficient as your fieldwork needs to be.
📞 Get Your EP-68 Quote Today
Stop losing field time to gearbox failures. The EP-68 is built to run all season without skipping a beat. Talk to our specialists about the right configuration for your operation.
