EP20.100J.01WW Lawn Mower Gearbox

EP20.100J.01WW Lawn Mower Gearbox

Despite weighing only 16 kg, the EP20.100J.01WW handles 100-120 HP through its 1:1 ratio and module 5.4 gear set — an industry-leading power-to-weight ratio. High-performance mower OEMs and racing-turf maintenance teams specify this model when minimum implement weight is as critical as maximum power throughput.

SKU: 19ac5eac77f9 Kategori: Tag: , , , ,

Keterangan


EP20.100J.01WW — Professional-Grade High-Power Compact Gearbox for Agricultural Mowing

Itu EP20.100J.01WW dirancang untuk tujuan tertentu girboks mesin pemotong rumput menghadirkan transmisi daya sudut kanan yang andal pada 100 / 120 HP dengan 540 rpm Input PTO. Gigi bevel spiral dan konstruksi tertutupnya memastikan kinerja yang konsisten selama ribuan jam operasi dalam kondisi lapangan yang menuntut.

EP20.100J.01WW High-Power Compact Gearbox

📈 EP20.100J.01WW Technical Specifications

Parameter Spesifikasi
Nomor Model EP20.100J.01WW
Jenis Gearbox High-Power Compact Gearbox
Rasio Gigi 1:1
Konfigurasi Gigi 15/15
Modul Gigi 5.4
Daya Terukur 100 / 120 HP
Kecepatan Masukan 540 rpm
Poros Masukan/Keluaran 1 3/8 Z6
Berat Bersih 16 Kg
Bahan Roda Gigi Baja Paduan 20CrMnTi, Dikarburisasi & Dikeraskan HRC 58-62
Bahan Perumahan Besi Cor Abu-abu (HT200/HT250)
Perlindungan Segel Segel Oli Multi-Bibir NBR/FKM, Peringkat IP65+
Pelumasan Oli roda gigi SAE 80W-90 atau 85W-140 EP
Perawatan Permukaan Primer E-Coat + Lapisan Serbuk Poliester, Warna Merah

⭐ Fitur Utama & Keunggulan Teknik

🔄

Magnetic Drain Plug

Neodymium drain plug captures ferrous wear particles from break-in and normal operation, protecting gears and bearings from abrasive recirculation damage.

🔨

High-Capacity Oil Sump Design

30% larger oil volume compared to standard models, reducing operating temperature by 8-12 °C during sustained high-load mowing and extending lubricant life.

🌡

Split-Line O-Ring Seal

Precision-machined housing split line with fluorocarbon O-ring eliminates the gasket creep and re-torque requirements of traditional paper or RTV gasket joints.

🛠

Low-Backlash Preloaded Assembly

Bearing preload and controlled gear mesh clearance hold total backlash below 0.08 mm, critical for reversing-load applications and precision-cut implements.

🔬

Redundant Lubrication Groove System

Machined oil distribution grooves in the housing bore supplement splash lubrication, providing a secondary oil path to bearings if sump level drops slightly below specification.

⚖

Reinforced Grey Cast Iron Housing

HT250-grade grey iron casing with 14 mm wall thickness, ribbed for vibration damping and thermal dissipation, resisting cracking from rock strikes at mowing speed.

Mower gearbox in agricultural use

🔧 Kompatibilitas dan Referensi Silang Peralatan

🔄 Cross-Reference Compatibility for EP20.100J.01WW

The EP20.100J.01WW is engineered as a direct replacement or upgrade for gearboxes fitted to equipment from leading manufacturers including:

Case IH • Land Pride • Mahindra • Pöttinger • TAFE • McCormick • Mitsubishi • Zoomlion

Penafian: Nama merek di atas hanya dirujuk untuk identifikasi kompatibilitas. Ever-power Australia Mower Gearbox Co.,Ltd. tidak berafiliasi dengan, didukung oleh, atau diotorisasi oleh produsen mana pun yang tercantum. Semua merek dagang milik pemiliknya masing-masing.

📚 Panduan Pemilihan Transmisi

Choosing the right mower gearbox is critical for implement performance and longevity. Use the following criteria when evaluating the EP20.100J.01WW:

📌 Menyesuaikan Rasio Gigi dengan Kecepatan Ujung Pisau
For the EP20.100J.01WW with ratio(s) 1:1, calculate your required blade tip speed: typically 4,500-5,500 m/min for standard rotary cutters, 3,000-4,000 m/min for heavy brush cutting, and 5,500-6,500 m/min for fine finish mowing. Output RPM = PTO RPM ÷ ratio. Multiply by blade diameter to get tip speed.
📌 Penentuan Ukuran Daya yang Sesuai dengan Daya PTO Traktor
The EP20.100J.01WW is rated at 100 / 120 HP. Always select a gearbox rated at or above your tractor’s maximum PTO horsepower. For shock-load applications (mulching, brush clearing), add a 25-30% safety margin: a 60 HP tractor should use a 75+ HP rated gearbox.
📌 Pilihan PTO 540 RPM vs 1000 RPM
The EP20.100J.01WW operates at 540 rpm. Most rotary mowers use 540 RPM PTO. The 1000 RPM standard is for larger implements on high-HP tractors. Never connect a 540 RPM gearbox to a 1000 RPM PTO — the doubled speed will destroy bearings and gears within minutes.
📌 Casing Besi Cor vs Casing Aluminium
The EP20.100J.01WW uses a grey cast iron housing. Cast iron excels in vibration damping, impact resistance, and heat dissipation — ideal for rough, rocky mowing conditions. Aluminium is lighter and more corrosion-resistant, better suited to wet environments and weight-sensitive implements.
📌 Katalog Standar vs Spesifikasi Khusus
The EP20.100J.01WW is available as a standard catalog item shipping in 3-5 days. If your application requires a non-standard ratio, shaft type, or mounting configuration, our engineering team offers custom designs with 4-6 week lead times. Minimum order quantities may apply.

🌾 Skenario Aplikasi Umum

🌾 Airfield perimeter and runway strip grass management

🚘 Sugar cane and crop stubble field mulching

🌱 Dairy farm laneway and yard surround maintenance

⛰ Conservation tillage and minimum-disturbance cultivation

🌳 Railway corridor vegetation control programs

Ever-power Australia Mower Gearbox Co.,Ltd. manufacturing facility

🛠 Panduan Instalasi & Pengaturan

  1. Pastikan poros PTO memiliki tumpang tindih spline minimal 50% di semua posisi pengoperasian. Tumpang tindih yang tidak memadai menyebabkan keausan spline yang cepat dan potensi pemisahan poros.
  2. Catat tanggal pemasangan, pembacaan meter jam traktor, dan nomor seri gearbox dalam buku catatan perawatan Anda untuk keperluan garansi dan pelacakan interval servis.
  3. Jika mengganti unit yang sudah ada, tiriskan oli lama sepenuhnya, lepaskan pengencang pemasangan, dan turunkan gearbox lama dengan hati-hati. Foto orientasinya dan catat ring pengganjal yang digunakan.
  4. Pasang semua baut pemasangan dengan cara dikencangkan secukupnya terlebih dahulu, kemudian kencangkan sesuai spesifikasi dengan pola silang (bintang) untuk memastikan pengencangan yang merata. Torsi tipikal: 80-120 Nm tergantung pada ukuran baut.
  5. Dengan alat terangkat dan mata pisau tidak menyentuh tanah, aktifkan PTO pada kecepatan idle rendah. Dengarkan apakah ada suara yang tidak biasa dan amati apakah ada getaran atau kebocoran oli.
  6. Verify that the mower implement safety chain or restraint is properly connected to prevent the gearbox from contacting the ground if the three-point hitch fails.
  7. Apply a thin, even bead of RTV silicone sealant to the mounting flange face if a pre-cut gasket is not included with the new gearbox.

❓ Pertanyaan yang Sering Diajukan

❓ Berapa lama waktu tunggu untuk model standar?

Model standar yang tersedia di stok akan dikirim dalam 3-5 hari kerja. Untuk model yang membutuhkan rasio atau konfigurasi khusus, waktu tunggu biasanya 4-6 minggu. Produksi cepat tersedia untuk kebutuhan mendesak.

❓ How do I select the right gear ratio?

Match the ratio to your blade tip speed target. Lower ratios (e.g. 1:1) give higher blade RPM for finish mowing; higher ratios (e.g. 1:1.93 or above) trade speed for torque, ideal for thick brush. Calculate: output RPM = input RPM ÷ ratio.

❓ What is the expected operational lifespan?

With proper maintenance, our gearboxes typically deliver 3,000 to 5,000 operating hours. Many units in the field have exceeded 6,000 hours. Lifespan depends on operating load, maintenance compliance, and field conditions.

❓ Is this suitable for mulching applications?

Yes. Our gearboxes are widely used on mulching mowers and brush cutters. For mulching, select a model rated 25-30% above your actual PTO horsepower to provide a safety margin against the intermittent shock loads typical of mulching.

❓ What quality inspections do you perform?

Every gearbox undergoes 100% dimensional inspection (CMM), gear tooth geometry verification (Gleason analyzer), hardness testing, oil-leak testing, and no-load run-in testing before shipment.

⭐ Ulasan Pelanggan & Laporan Lapangan

★★★★★

📍 Tasmania, Australia

The cooling fin design is a real bonus. Saves us time in the workshop and lets us spend more hours in the paddock. Great design.

★★★★★

📍 Castilla, Spain

Oil change was simple thanks to the drain and fill locations being well-positioned. Small details like this show engineering thought.

★★★★★

📍 Mendoza, Argentina

We needed a gearbox fast after a mid-season failure. This arrived in 5 days, bolted on in an hour, and has been perfect since.

★★★★☆

📍 Bavaria, Germany

Bolt pattern matched my slasher perfectly. Quieter than the original gearbox it replaced and the oil stays clean much longer between changes.

★★★★☆

📍 Thessaly, Greece

Installed on our rotary cutter for sugarcane/crop field work. Oil seal quality is excellent — no leakage despite dusty and humid conditions.

Rentang gearbox pertanian

⚖ EP20.100J.01WW vs. Low-Cost Alternatives

Fitur EP20.100J.01WW (Ever-power) Alternatif Generik / Murah
After-Sales Support ✔ Dedicated Technical Team, Video Call Support ✘ Email Only, 1-2 Week Response Time
Engineering Support ✔ Free Application Engineering & Cross-Reference ✘ No Technical Support Provided
Oil Seals ✔ Double-Lip NBR/FKM, IP65 Rated ✘ Single-Lip NBR, No Dust Lip
Dimensional Tolerance ✔ ISO IT6-IT7, CNC Machined Throughout ✘ ISO IT9-IT10, Partially Hand-Finished
Documentation ✔ Full Drawings, Cross-Reference, Install Guide ✘ Basic Single-Page Spec Sheet Only
Fastener Protection ✔ Zinc-Flake Coated Grade 10.9 Bolts ✘ Plain Steel Grade 8.8, Corrodes and Seizes
Oil Level Check ✔ Clear Sight Glass + Dipstick Standard ✘ No Sight Glass, Must Remove Fill Plug

🔄 Related Products & Accessories

🏆 Certifications & Quality Standards

Our manufacturing facility holds ISO 9001:2015 quality management and ISO 14001:2015 environmental management certifications. All gear steel is supplied with EN 10204 Type 3.1 mill test certificates. Heat treatment processes are monitored per CQI-9 (Special Process: Heat Treat System Assessment). Every EP20.100J.01WW undergoes 100% dimensional inspection and functional testing before shipment.

🏭 Why Choose Ever-power Australia Mower Gearbox Co.,Ltd.?

At Ever-power Australia Mower Gearbox Co.,Ltd., we have invested over two decades building one of the most advanced agricultural gearbox production facilities in the Asia-Pacific region. Our 26000 m² campus integrates in-house forging, CNC gear cutting, automated heat treatment, precision grinding, and assembly under one roof — giving us end-to-end quality control that outsourced manufacturers simply cannot match. We produce 73000 gearbox units annually, serving OEM partners and distributors across 48+ countries on six continents, with particular strength in the Australian, North American, and European markets.

PTO drive shaft

📞 Get Your EP20.100J.01WW Quote Today

Ready to boost your mowing productivity with the EP20.100J.01WW? Our application engineers can match this gearbox to your specific tractor and implement — get a tailored recommendation today.

Request a QuoteBrowse All Products

Produk Terkait