Gearbox for Beet Harvester

Your tractor’s PTO shaft engages with the gearbox through a hardened splined input shaft. The interface transmits torque while allowing minor angular misalignment. Inside, needle roller bearings support the input shaft and manage the combined loading of transmitted torque and driveline forces.

The heart of the gearbox is a matched set of helical gears, forged from Cr-Mo alloy steel. These gears reduce rotational speed from PTO RPM to the topper/lifter drive’s working speed while proportionally multiplying torque. The beet harvester gearbox powers the topping mechanism, lifting shares, and cleaning turbines. Positioned on the harvester mainframe, it coordinates multiple outputs at different speeds — fast for the topper, moderate for lifting, and variable for the cleaning stages. The gear mesh geometry is computer-optimized for even load distribution.

The transformed power exits through the output shaft to the beet harvester’s working mechanism, specifically driving the topper/lifter drive for core beet harvesting function. The output connection is engineered for vibration-free, backlash-free transmission at the point of work.

The gearbox uses splash lubrication with ISO VG 220 EP. Gears distribute oil across all contact surfaces. The grey cast iron housing incorporates cooling ribs that dissipate heat under sustained beet harvesting load. Viton Fkm Lip Seals at every shaft exit prevent contamination ingress.

Align the PTO driveline with the gearbox input shaft and slide the yoke onto the splines until the locking mechanism engages. Verify the spline count matches (6-spline for 540 RPM, 21-spline for 1000 RPM). Check that driveline operating angles do not exceed 15° — excessive angles cause premature U-joint failure and vibration.

Clean the mounting flange on the beet harvester frame with a wire brush and solvent, removing all old sealant, rust, and debris. Inspect the mounting surface for cracks, stripped threads, or warping. Chase any damaged bolt threads with a tap. Apply a thin film of anti-seize compound to the mounting face if specified.

Start the tractor and engage the PTO at low RPM (approximately 300 RPM). Listen carefully for any grinding, whining, knocking, or clicking sounds. Run at low speed for 15-20 minutes, monitoring the gearbox housing temperature by hand (carefully). Check for oil leaks at all seals and the mounting interface. Gradually increase to full operating speed.

Disconnect the PTO driveline from the gearbox input shaft. Support the gearbox weight with a floor jack or overhead hoist (typical weight: 15-70 kg depending on model). Remove all mounting bolts in a criss-cross pattern to relieve clamping stress evenly. Carefully lower the old gearbox and set it aside.

Attach the gearbox output shaft to the beet harvester’s topper/lifter drive drive coupling. For keyed connections, align the keyway and slide the coupling on, then secure with the retaining bolt and torque to specification. For splined outputs, apply anti-seize to the splines and verify full engagement before locking.

Remove the fill plug and slowly add the recommended gear oil until it reaches the level indicator. Use the lubricant grade specified in the gearbox documentation (typically SAE 80W-90 GL-5 or equivalent). Replace the fill plug and hand-tighten, then snug with a wrench. Verify the breather cap is clean and unobstructed.

Park the tractor on firm, level ground. Engage the parking brake and place wheel chocks. Turn off the engine and remove the key. Disconnect the PTO shaft from the beet harvester. Allow all components to cool completely before touching. Wear appropriate PPE including gloves and safety glasses.

Probable Cause: PTO tahrik milinin yanlış hizalanması, mafsal açısı sınırlarını aşıyor.

Recommended Action: First check all mounting bolt torques — vibration frequently loosens fasteners, which then amplifies the vibration. Next, inspect the PTO driveline U-joints for wear or binding. Verify driveline angles are within specification. Finally, check the output coupling to the topper/lifter drive for wear or damage.

Probable Cause: Aşınmış dudak contaları veya hasarlı conta yuvası

Recommended Action: First, check and correct the oil level — overfilling is a surprisingly common cause of seal leaks. Clean or replace the breather cap. If oil level is correct and breather is clear, the seal has worn and should be replaced using our seal kit.

Probable Cause: Farklı PTO standardı nedeniyle hizasız kamalar

Recommended Action: Clean the input shaft splines with a wire brush and apply a light coat of anti-seize. Slowly rotate the PTO shaft while pushing to align the splines. If the splines will not engage, verify the spline count matches your PTO standard — 6-spline for 540 RPM, 21-spline for 1000 RPM.

Probable Cause: Aşınmış veya çukurlaşmış dişli yüzeyleri

Recommended Action: Drain and inspect oil for metal particles. Refill with correct grade. If noise persists after oil change, bearing or gear inspection is required. Contact support for rebuild guidance.

Probable Cause: Aşınmış dişlilerde aşırı geri tepme

Recommended Action: A clunking sound specifically on PTO engagement (but not during operation) usually indicates driveline lash — check driveline telescoping tube for wear. If the clunk occurs during operation, it may indicate excessive gear backlash from internal wear. Have the gearbox inspected if the sound is progressive.

Absolutely. We manufacture gearboxes with keyed, splined, flanged, hex, and hollow-bore output shaft configurations. If your beet harvester requires a non-standard output size, spline count, or connection type, our engineering team will design and machine it to your exact specifications at no additional lead time for common modifications.

Ödemelerinizi banka havalesi, kredi kartı ve mevcut hesaplardan gelen satın alma siparişleriyle kabul ediyoruz. Büyük siparişler için, kredi onayı şartıyla 30 günlük ödeme süresi sunuyoruz. Siparişlerinizi web sitemiz üzerinden, e-posta yoluyla veya telefonla verebilirsiniz. Ön ödeme düzenlemeleri için proforma faturalar mevcuttur.

Yes — every purchase includes access to our engineering support team for installation guidance, troubleshooting, maintenance advice, and parts ordering. Support is available via phone, email, and our online contact form. There is no charge for technical support during or after the warranty period.

Her bir şanzıman, nakliye sırasında boşaltılan yağdan arındırılır, VCI (Buhar Korozyon Önleyici) filmle sarılır ve uluslararası nakliye için uygun, sağlam bir kontrplak kutuya yerleştirilir. Bu ambalaj, nakliye sırasında nem, darbe ve korozyona karşı koruma sağlar; hatta karayolu taşımacılığıyla Avustralya'nın uzak bölgelerine yapılan gönderilerde bile.

For most Australian climates, SAE 80W-90 EP gear oil meeting GL-5 specification is ideal. In tropical regions with sustained high temperatures, we recommend 85W-140. For southern regions experiencing cold winters, synthetic 75W-90 provides better cold-start protection. Check the oil specification card shipped with your gearbox for the definitive recommendation.

Rutin bakım (yağ değişimi, keçe değişimi, rulman kontrolü) standart aletlerle yerinde yapılabilir. Büyük çaplı revizyonlar için, tüm rulmanları, keçeleri ve contaları içeren komple revizyon kitleri tedarik ediyoruz. Detaylı servis kılavuzları ve video rehberleri destek portalımızdan indirilebilir.

Our gearbox matches or exceeds OEM specifications across all measurable parameters. Key improvements include upgraded bearing classes, superior seal materials, enhanced heat dissipation, and the option for custom gear ratios that OEM catalogues do not offer. The result is a drop-in replacement that typically outlasts the original.

Her şanzıman şu parçalarla birlikte gönderilir: tork özelliklerini içeren kurulum kılavuzu, yağlama ve bakım programı, parça numaralarını gösteren parça şeması, garanti kayıt kartı ve ünitenin seri numarası ve test sonuçlarını içeren kalite kontrol sertifikası.

Evet, Avustralya'nın her posta koduna, uzak ve bölgesel alanlar da dahil olmak üzere gönderim yapıyoruz. Mevsimlik ekipman ihtiyaçlarının aciliyetini anlayan deneyimli tarım ekipmanı taşıyıcılarıyla çalışıyoruz. Acil arıza durumları için ekspres kargo seçeneği mevcuttur ve popüler modellerin hemen gönderilmesi için stok bulunduruyoruz.

Our 24-month comprehensive warranty covers all defects in materials and workmanship, including bearings, gears, seals, and housing. It applies from the date of purchase and is backed by our ISO-certified quality management system. Extended warranty programs are available for bulk and fleet orders.